2 June 2022 in IEEE Open Journal of the Industrial Electronics Society
The emphasis on clean and green technologies to curtail greenhouse gas emissions due to fossil fuel-based economies has originated the shift towards electric mobility. As on-road electric vehicles (EVs) have shown exponential growth over the last decade, so have the charging demands. The provision of charging facilities from the low-voltage network will not only increase the distribution system's complexity and dynamics but will also challenge its operational capabilities, and large-scale upgrades will be required to meet the inevitably increasing charging demands. An ultra-fast (UF) charging infrastructure that replicates the gasoline refueling network is urgently needed to facilitate a seamless transition to EVs and ensure smooth operation. This paper presents a review of state-of-the-art DC fast chargers, the charging infrastructure's current status, motivation, and challenges for medium-voltage (MV) UF charging stations (UFCS). Furthermore, we consider the possible UFCS architectures and suitable power electronics topologies for UF charging applications. To address the peak formation issues in the daily load profile and high operational expenses of UFCSs, integration of renewable energy sources and energy storage systems due to their technological and economic benefits is being considered. The benefits of line frequency transformer (LFT) replacement with a solid-state transformer (SST),SST models, SST-based UF chargers, and MV SST-based UFCS architectures, as well as related MV active front-end and back-end power electronics topologies, are presented. Finally, the application of microgrids' hierarchical control architecture is considered for chargers and system-level control and management of UFCSs.
3 August 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Battery storage system (BSS) integration in fast charging station (FCS) is becoming popular to achieve higher charging rates with peak-demand shaping possibility. However, the additional conversion stage for integrating the BSS increases the system losses, size and cost. The concept of partial power processing converter (PPPC), can mitigate this effect. Compared to conventional used full power processing converter, PPPC reduces the amount of transferred power from the BSS to the electric vehicle by the converter. As a consequence, the power losses generated by the converter are reduced, leading to lower sized converters and higher system efficiencies. This paper proposes a DC/DC multiport converter which allows the integration of battery storage in FCS based on a partial power processing concept, while maintaining the specific requirements in terms of isolation for FCS. The proposed three-port partial power processing converter (3P-PPPC) is derived from the commonly used triple active bridge (TAB) converter. The resulting design trade-offs, the dynamic behavior and limitations of the topology are investigated. Furthermore, the round-trip efficiency of the 3P-PPPC for integrating BSS in FCS is compared with conventional full power processing converter solutions, highlighting the superiority of the proposed topology. A prototype has been built to validate the 3P-PPPC.
3 July 2023 in IEEE Open Journal of Power Electronics
Multilevel converters (MLCs) are widely recognized for their exceptional benefits and have emerged as the preferred choice for medium- and high-power/voltage applications. Their usage has also been extended to low-power applications to overcome issues associated with high switching frequencies and electromagnetic interference (EMI) commonly encountered in two-level converters. Common dc-link MLCs have received particular attention in industry due to their ability to eliminate the need for bulky and inefficient transformers and rectifiers, making them a compelling option for different applications, primarily medium- and high-power/voltage applications such as wind turbine (WT) power conversion systems. Furthermore, common dc-link topologies are required for back-to-back (BTB) configurations, as they facilitate the use of a shared dc-link between the rectification and inversion stages. Despite their popularity, there is currently no comprehensive review article dedicated to common dc-link topologies. This paper addresses this gap by presenting a comprehensive review of common dc-link MLCs, covering their topological evolution, features, topologies comparison, modulation techniques, control strategies, and industrial application areas. Additionally, future perspectives and recommendations are discussed to provide researchers and engineers with a better understanding of the potential applications and advantages of these converters.
12 April 2024 in IEEE Transactions on Power Electronics
Multiport architectures based on multiwinding transformers allow the connection of multiple electrical components to achieve smart home functionality. However, existing solutions use full-power semiconductor devices or are constrained by the complexity of the multiwinding transformer design. As an alternative, this work proposes a new multiport partial power converter (PPC) architecture. The proposed multiport PPC architecture enables the partial power by using the series resonant converter based dc transformer. In contrast to the prior art solutions, the proposed converter can be built using partial power semiconductor devices, and only a single transformer rated for a part of the overall power is required. The operating principle and design criteria are also described in the article. The effect of partial power utilization is analyzed in detail. Finally, the proposed topology has been validated using a 3 kW prototype.
18 January 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Maximum Power Point Tracking (MPPT) in solar photovoltaic (PV) systems is predominantly achieved by full power DC-DC converters (FPC). Alternatively, partial power DC-DC converters (PPCs) process only a portion of the full power to achieve MPPT. Other goals of PPCs are a higher efficiency, a higher power density and a lower overall cost compared to FPCs (e.g. by using lower voltage class and/or lower current semiconductors). The flyback PPC topology shows that efficiency can be improved by 1% in comparison to FPCs. However, the use of transformers with large self-inductance tends to increase the volume. An alternative architecture is proposed in this work based on a series resonant converter (SRC). The addition of this partial power SRC stage pays off in terms of current ripple mitigation, reduced volume and high efficiency. The analysis and design of the proposed converter is presented in detail. The advantage of the proposed PPC architecture is highlighted by volume and loss comparisons. The analyzed efficiency and the practical efficiency measurement results are compared. The concept is experimentally validated using a 1.6kW prototype.
20 March 2023 in IEEE Transactions on Power Electronics
The exploitation of PCB integrated magnetic components in the high power field brings new challenges due to the compactness of the design and the poor thermal performance of components using standard PCB technology. In this work, a thermal modelling approach is proposed which is suitable for optimization based design of planar PCB magnetic components. The targets are high accuracy, low computation time and easy implementation. The results show an accuracy comparable to Finite Element simulations, with average absolute error of 1.3 $^{\circ }$ C respect to measurement, while the computation time is 13 times shorter than simplified Finite Element simulations. The equations are purely analytical, i.e. no measurements or simulations are needed to obtain the involved parameters. The structure of the model enables easy and fast generation of PCB geometries, with the possibility to make a parametric sweep of any variable. The model has been verified with Finite Element simulations and experimental measurements for a wide range of operating conditions, including dc and ac excitation.