Serhiy V. Adzhamskyi

Serhiy V. Adzhamskyi

Auto-generated profile, based on publicly available information

Serhiy V. Adzhamskyi

PhD, Chief Designer of LLC "Additive Laser Technology of Ukraine", senior researcher at the Institute of Transport Systems and Technologies of the National Academy of Sciences of Ukraine

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022
Verified
Book
Closed access
LULLC «Additive Laser Technology of Ukraine»
LLC «Additive Laser Technology of Ukraine»
SASergey Adjamskiy
Sergey Adjamskiy
GKGanna Kononenko
Ganna Kononenko
Rostyslav PodolskyiRostyslav Podolskyi
Rostyslav Podolskyi
SBSergey Badyuk
Sergey Badyuk
Additive technologies make it possible to provide high quality products (accuracy and uniqueness of geometry, high complex of mechanical properties, high density (low porosity), uniformity of microstructure and chemical composition). A wide range of materials used allows it to find application in such industries as medical and dental, engineering, automotive and aerospace. At present, technological capabilities, the development of laser technologies and CAD modeling systems have made it possible to develop devices for building parts by loading the original CAD model and fusing metal powder using a laser in accordance with it – what is today called SLM technology. During this process, the metal powder is completely melted under the influence of high-power laser radiation with the formation of a metal layer that contains almost no pores and does not require further processing, which makes it possible to achieve a level of mechanical properties of the product equal to or even better than those of cast ones. To create advanced equipment and professional control of the process of manufacturing parts, a deep understanding of the processes occurring in the melt pool under the laser beam and after hardening is necessary. At the same time, the final quality of products manufactured using SLM technology depends on many factors that can be divided into main groups: equipment (calibration, laser power, energy distribution in the beam, powder application system, shielding gas supply, distribution and purification system, system ensuring the tightness of the chamber, etc.), material (sphericity, dispersion, bulk density, fluidity, properties, handling, etc. of metal powder), process parameters, geometry features of the part, finishing. Prospects for the development of technology in Ukraine are associated with the development of new structural materials, solving topology optimization problems, prototyping, studying the properties of materials and creating the latest production solutions in the field of additive technologies.

28 September 2022 in Science and innovation
Verified
Journal Article
Closed access
PDF file
САС. Аджамський
С. Аджамський
ГКГ. Кононенко
Г. Кононенко
РПР. Подольський
Р. Подольський
СБС. Бадюк
С. Бадюк
Introduction. The additive manufacturing technologies have recently become more widespread in modern production, as they allow the quick and efficient manufacture of products with a unique geometry. Problem Statement. For the production of parts, it is necessary to use rational technological parameters that depend on the characteristics of the material and equipment for selective laser melting (SLM). Among the factors affecting the mechanical properties there are the sample orientation in the working chamberand the thickness of the working layer. Purpose. The purpose of this research is to study the effect of sample orientation in the direction of the X, Y, Z axes and layer thickness (40 and 20 μm) on the physical and mechanical properties of the Co-Cr-Mo alloy fabricated by the selective laser melting method. Material and Methods. All prototypes are made of Co-Cr-Mo alloy powder with a particle size of 10–45 μm. The samples are printed with layer thicknesses of 20 and 40 μm, with the use of an Alfa-150 3D printer manufactured by ALT Ukraine LLC. The samples for tensile tests are placed on the platform in horizontal (X and Y axes) and vertical (Z axis) positions. The tests to determine the mechanical properties have been carried out in accordance with ISO 6892:2019, on a PHYWE testing machine. The thermal expansion coefficient has been determined with the use of a DIL.A.802 dilatometer. Results. The dependence of the metaldensity at a constant thickness of the deposited layer of 40 and 20 μm and a distance between tracks of 0.1—0.12 mm has been established, and the rational conditionsfor manufacturing samples for tensile tests have been chosen. Conclusions. It has been established that a decrease in the intertrack distance contributes to the achievement of a density of 99.99% and an increase in the area of the rational printing conditions. It has been shown that the samples printed with different thicknesses of the working layer have different mechanical properties. When comparing samples made at different layer thicknesses and placed in the same direction, we have found that the temporary resistanceis the lowest for the vertical samples as compared with the horizontal ones in the X and Y directions.

28 April 2021 in Aerospace technic and technology
Verified
Journal Article
Closed access
PDF file
САСергій Вікторович Аджамський
Сергій Вікторович Аджамський
ГКГанна Андріївна Кононенко
Ганна Андріївна Кононенко
РПРостислав Вячеславович Подольський
Ростислав Вячеславович Подольський
СБСергій Іванович Бадюк
Сергій Іванович Бадюк
Additive manufacturing technology, also known as 3D printing, has become an increasing amount of popular lately, and the number of materials and methods that can be used is expanding. As manufacturing processes continue to improve and evolve, the demand for faster, less expensive manufacturing processes has enabled a range of Rapid Prototyping (RP) processes to be developed. Since production processes continue to evolve and grow, the demand for faster and less expensive production processes has allowed the development of a series of processes of rapid prototyping (RP). With additive manufacturing, virtually any geometry with variations in size and complexity can be produced with a high degree of accuracy. The typical microstructure of the metal after the completion of the construction process is the dispersed dendritic and cellular structures of the γ-phase within the melt baths of single tracks, because of the overlap of which a part is created layer by layer. The main problems of ensuring high-quality products using SLM technology are porosity, hot cracking, anisotropy, surface roughness, and ensuring the necessary microstructure of the synthesized material. Improvement of surface roughness, the brilliance of stainless steel surface elements after electrochemical polishing (EP) is one of the most important characteristics of the process. Samples were made using the SLM technology from austenitic steel powder AISI 316L with a controlled defect in the form of local overheating, because of which an orange variability is formed, which is formed during 3-D printing. The samples are inversely symmetrical, have an equilateral trapezoid shape with bases of 20 and 5 mm, a height of 10 mm, and a thickness of 5 mm. The main body of both samples was printed in the same modes at a power of 220 W, a speed of 1000 mm / s, and a track spacing of 0,14 mm. To form a controlled defect when printing the boundaries of the samples, the following modes were used: power 120 W, speed 1050 mm / s, and distance between tracks 0,02 mm. The samples were printed in an Alfa-280 3D printer manufactured by ALT Ukraine. Etching to reveal the microstructure of the samples was conducted using an HCl + HNO3 solution. Electropolishing was conducted in a solution of orthophosphoric acid (H3PO4) with glycerol (C3H8O3) at a current density of 3 A / cm2. Metallographic studies have shown that the configuration of the tracks in the area of increasing the cross-section of the samples is more uniform. Based on this study, schemes for distributing zones with varying degrees of track equiaxiality and structure uniformity were constructed. A more intense interaction of the reagent with the microstructure near the surface with greater roughness was found. The electropolishing of isosceles trapezoids occurred in three stages: 1) visual - optical examination with fixation, control of roughness, weight, and geometry before starting the process; 2) control of roughness and geometry after 3 min. process; 3) visual - optical examination with fixation, control of roughness, weight, and geometry after 6 min electropolishing. From the analysis of the obtained roughness data and the real volt-ampere curve, it was found that zone 2 with the largest area had an insignificant change in roughness, zone 1 and zone 3 with a decrease in the area had a more significant loss on average by 33%. Controlling the weight before and after the test showed that the samples lost approximately the same weight of about 1,5%. Based on the ratio of the results obtained, it was found that when a fixed current strength and constant power are applied, electropolishing is not effective for active uniform anodization of the surface of a simple figure with a change in the area in the section. It was found that electropolishing most intensively occurs in an area with a smaller cross-sectional area.

1 January 2020 in Scientific journal of the Ternopil national technical university
Verified
Journal Article
Open access
SAS. Adjamskiy
S. Adjamskiy
GKG. Kononenko
G. Kononenko
Rostyslav PodolskyiRostyslav Podolskyi
Rostyslav Podolskyi
Additive manufacturing is a promising modern direction that allows quickly and with high accuracy layer-by-layer manufacture of complex-shaped products using a computer model from almost any metal powders. This work is devoted to the study of the influence of specimen orientation during 3-D printing and heat treatment modes on the mechanical properties of specimens made of Inconel 718 heat-resistant nickel alloy manufactured using SLM technology. In the study of the position of the specimen during printing, it was found that the strength indicators are slightly higher for vertical specimens (up to 9%), and the plasticity is lower on average by 20%. After standard heat treatment, which consists of two stages (quenching and aging) with cooling in quiet air, the strength values of vertically and horizontally constructed specimens are very close (the difference is up to 3%).The plasticity values for the horizontal position of the specimen when printing are 10% and 30% higher. According to macrogeometry, the specimens under study have cup fracture; according to microfractors, it was established that the fracture mechanism is viscous and quasi-brittle. In the initial state, which is formed by 3-D printing, there were signs of viscous fracture: the crack propagates mainly by separating the metal in planes that do not coincide with the crystallographic planes of the sections, mainly the fracture surface in the form of pits - microdepressions on the fracture surface. representing the exposed surfaces of the microvoids formed during the plastic flow of the metal. In the study of the metal of the test specimens in the polished state, it was found that specimens No. 1-5 had high integrity (low porosity), a small amount of oxide inclusions was observed. The study found that the presence of defects in the form of micropores did not lead to a significant reduction in the mechanical properties of the test samples.

1 January 2022 in Fundamental and applied problems of ferrous metallurgy
Verified
Journal Article
Closed access
GKG. A. Kononenko
G. A. Kononenko
IUIron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
SAS. V. Adjamsky
S. V. Adjamsky
Rostyslav PodolskyiRostyslav Podolskyi
Rostyslav Podolskyi
OSO. A. Safronova
O. A. Safronova
UTUkrainian State University of Science and Technologies
Ukrainian State University of Science and Technologies
The purpose of the work is to study the microstructure and mechanical properties of 316L stainless steel samples made by the SLM method. 316L stainless steel has been extensively studied for the state after fabrication by selective laser melting (SLM). This is due to the wide use of this material in various industries, as it demonstrates sufficient corrosion resistance and excellent plasticity. Thus, its application can be found in the biomedical, aerospace, automotive and marine fields. Some of the studies conducted have shown the ability of SLM to improve the mechanical properties of parts compared to traditional methods. Metallographic analysis, determination of mechanical properties, and chemical analysis were used. The object of the study was austenitic grade 316L stainless steel. The material for making the samples was a 316L alloy powder with a particle size of 45 + 15 μm. Experimental samples for tensile tests were built on the equipment of "Additive Laser Technologies of Ukraine" LLC (Alfa-150) using SLM technology in identical modes: laser power - 290 W, scanning speed - 1100 mm/s, distance between tracks – 0.11 mm, scanning strategy - checkerboard fields, scanning order - Zig-Zag, field size - 5 mm, rotation of the layer relative to the previous one - 67°. From the results of the analysis of mechanical properties, it was established that the samples made on the 3-D printer of Additive Laser Technologies of Ukraine LLC are not inferior in terms of quality to leading global companies, and in some characteristics even exceed them. It should be noted that the results of determining the characteristics of the experimental samples were compared with the properties of the samples manufactured according to the optimal process parameters on the equipment of different manufacturers, but do not include the influence of the thickness of the applied layer. Comprehensive studies of the mechanical properties of the samples made of 316L steel showed full compliance with the samples produced on the equipment presented on the world market for the production of special-purpose products.

24 August 2023 in Aerospace technic and technology
Verified
Journal Article
Open access
PDF file
SASergey Adjamskiy
Sergey Adjamskiy
GKGanna Kononenko
Ganna Kononenko
Rostyslav PodolskyiRostyslav Podolskyi
Rostyslav Podolskyi
SBSergey Baduk
Sergey Baduk
In recent years, the actual production of metal products directly from electronic data according to a three-dimensional model based on layer-by-layer manufacturing has evolved from rapid prototyping to additive manufacturing. As the quality of additively manufactured metal products continues to increase and their manufacturing processes improve and develop, the demand for additive manufacturing is increasing. Additive manufacturing technology, also known as 3D printing, has become increasingly popular recently. Using additive manufacturing, almost any complex geometry can be manufactured with high degree of precision. After the production of parts using the SLM technology from metal powder, post-processing is applied, in particular electrochemical polishing, the main purpose of which is to reduce surface roughness, increase the gloss of surface elements, and remove metal powder that has partially melted onto the outer surface of the product at the point of contact between the molten metal and the border of the part and the powder, which is located next to the melt. This is especially important for inclined surfaces, internal channels and cellular structures with developed outer surface. For research, samples were made using SLM technology from AISI 316L austenitic steel powder. The samples have a cube shape with a base of 10 mm, a height of 10 mm, and a thickness of 10 mm, with cell widths of 4 mm and 2 mm. The main body of both samples was printed using the same modes at a laser power of 220 W, a scanning speed of 1000 mm/s and a distance between laser passes of 0.14 mm. Samples were printed on Alfa-280 3D printer manufactured by ALT Ukraine LLC. Electropolishing was carried out in a solution of orthophosphoric acid (H3PO4) with glycerol (C3H8O3) by immersing the test samples in the electrolytic solution at a voltage of 17 V and a current density of 3 A/cm2. The control of weight and geometric parameters was carried out with the help of ADV-2000 analytical balances and MKC-25 micrometer. The electropolishing of the experimental samples took place in four stages: 1) visual - optical inspection with fixation, weight control before the start of the process; 2) electropolishing for 3 minutes, visual - optical inspection with photo fixation; weight control after 3 min. polishing process; 3) electropolishing of the same samples for another 3 minutes, visual – optical inspection with photo fixation, weight control after 6 minutes. polishing; 4) electropolishing of the same samples for another 3 minutes, visual - optical inspection with photo fixation; weight control after 9 min. electropolishing process. At each stage, a real current-voltage curve was recorded using an oscilloscope. As a result of weight control before and after the test, it was established that the samples lost approximately the same weight in the range of 6.9...7.1 % relative to the initial one. Based on the analysis of the obtained results, it was established that at a current density of 3 A/cm2 and at a voltage of 17 V, effective active uniform polishing of the surface of samples with a cellular structure of scaffold type with a variable cell size from 4 to 2 mm is realized.