7 December 2020 in Superconductor Science and Technology
Although the high-temperature superconducting (HTS) REBa 2 Cu 3 O
x
(REBCO, RE–rare earth elements) material has a strong potential to enable dipole magnetic fields above 20 T in future circular particle colliders, the magnet and conductor technology needs to be developed. As part of an ongoing development to address this need, here we report on our CORC ® canted cos θ magnet called C2 with a target dipole field of 3 T in a 65 mm aperture. The magnet was wound with 70 m of 3.8 mm diameter CORC ® wire on machined metal mandrels. The wire had 30 commercial REBCO tapes from SuperPower Inc. each 2 mm wide with a 30 µ m thick substrate. The magnet generated a peak dipole field of 2.91 T at 6.290 kA, 4.2 K. The magnet could be consistently driven into the flux-flow regime with reproducible voltage rise at an engineering current density between 400–550 A mm −2 , allowing reliable quench detection and magnet protection. The C2 magnet represents another successful step towards the development of high-field accelerator magnet and CORC ® conductor technologies. The test results highlighted two development needs: continue improving the performance and flexibility of CORC ® wires and develop the capability to identify locations of first onset of flux-flow voltage.
4 December 2017 in IEEE Transactions on Applied Superconductivity
A next step of energy increase of hadron colliders beyond the LHC requires high-field superconducting magnets capable of providing a dipolar field in the range of 16 T in a 50-mm aperture with accelerator quality. These characteristics could meet the requirements for an upgrade of the LHC to twice the present beam energy or for a 100-TeV center of mass energy future circular collider. This paper summarizes the activities and plans for the development of these magnets, in particular within the 16 T Magnet Technology Program, the WP5 of the EuroCirCol, and the U.S. Magnet Development Program.
13 November 2017 in IEEE Transactions on Applied Superconductivity
Canted-cosine-theta (CCT) technology has been studied for its suitability for a future-circular-collider (FCC) main dipole in terms of magnetic and mechanical performance, electrothermal protectability, as well as efficiency. In this paper, we present lessons learnt from our search for efficient CCT solutions by means of two-dimensional (2-D) magnetic and mechanical simulations, discuss the 3-D periodic mechanical model, as well as 3-D electromagnetic analysis of the end regions. Temperature and voltage distributions during a quench under simplifying assumptions are discussed, and the magnet's efficiency is compared to that of other contenders in the FCC design study. The results qualify the CCT design as a contender for the FCC main dipole.
11 November 2016 in IEEE Transactions on Applied Superconductivity
Recent studies have shown that strong, alternating focusing magnets can be used to greatly increase the momentum acceptance of hadron therapy gantries. With the high gradients achievable with superconducting magnets a level of momentum acceptance can be reached which may have significant implications to medical gantries and to the introduction of superconducting technology in this area. The design of such a superconducting magnet system for a proton therapy gantry will be presented. The Canted-Cosine-Theta concept is extended to a curved magnet system generating the desired bending and alternating focusing fields for the achromatic optics. Magnetic, structural, and thermal analysis of this design is presented along with preliminary efforts towards fabrication and assembly of the curved magnet.
8 March 2022 in IEEE Transactions on Applied Superconductivity
As part of the US Magnet Development Program, Lawrence Berkeley National Laboratory (LBNL) is working on the development of high field stress-managed Nb $_{3}$ Sn dipole magnets using canted-cosine-theta (CCT) technology. As part of this program, a series of two layer magnets, CCT3/4/5, with short sample bore field of approximately 10 T and a 90 mm diameter open aperture have been designed, fabricated, and tested. The first magnet in the series, CCT3, was limited to less than 70% of the short sample current, this limitation is believed to be due to conductor damage. The second magnet in the series, CCT4, reached 86% of the short sample current, after changes to the groove geometry were made to accommodate dimensional changes in the cable during heat treatment. The third and final magnet of this series, CCT5, reached 88% of the short sample current with improved training relative to CCT4, after changes were made to the impregnation and assembly methods. While this two layer series was used to successfully demonstrate Nb $_{3}$ Sn CCT magnet technology, improvements in the training behavior of these magnets is desirable. For this purpose, a subscale program has been devised in order to probe the causes and explore reductions / improvements to training in stress-managed magnet technology. The subscale nature of the magnets allows for faster turnaround in the fabrication and testing process. In this paper, we present the design and test results for the first (baseline) subscale Nb $_{3}$ Sn CCT magnet and demonstrate that the subscale platform and the larger two-layer magnets produce similar training results.
22 February 2022 in IEEE Transactions on Applied Superconductivity
The most effective way to achieve very high collision energies in a circular particle accelerator is to maximize the field strength of the main bending dipoles. In dipole magnets using Nb-Ti superconductor the practical field limit is considered to be 8-9 T. When Nb 3 Sn superconductor material is utilized, a field level of 15-16 T can be achieved. To further push the magnetic field beyond the Nb 3 Sn limits, High Temperature Superconductors (HTS) need to be considered in the magnet design. The most promising HTS materials for particle accelerator magnets are Bi2212 and REBCO. However, their outstanding performance comes with a significantly higher cost. Therefore, an economically viable option towards 20 T dipole magnets could consist in an “hybrid” solution, where both HTS and Nb 3 Sn materials are used. We discuss in this paper preliminary conceptual designs of various 20 T hybrid magnet concepts. After the definition of the overall design criteria, the coil dimensions and parameters are investigated with finite element models based on simple sector coils. Preliminary 2D cross-section computation results are then presented and three main layouts compared: cos-theta, block, and common-coil. Both traditional designs and more advanced stress-management options are considered.