Jeremy David Weiss

Jeremy David Weiss

Auto-generated profile, based on publicly available information

Jeremy David Weiss

University of Colorado, Boulder, CO 80309, United States of America

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2010 in Superconductor Science and Technology
Verified
Journal Article
Closed access
MPM Putti
M Putti
IPI Pallecchi
I Pallecchi
EBE Bellingeri
E Bellingeri
MCM R Cimberle
M R Cimberle
MTM Tropeano
M Tropeano
CEC B Eom
C B Eom

12 February 2019 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
DLDanko C van der Laan
Danko C van der Laan
JWJeremy D Weiss
Jeremy D Weiss
DMDustin McRae
Dustin McRae
High-field, low-inductance superconducting magnets in particle accelerators and fusion machines require high operating currents, often in combination with high current densities and for some applications conductor bending radii of less than 50 mm. These requirements form a major challenge for magnet conductors consisting of high-temperature superconductors, which are required for reaching magnetic fields exceeding 20 T, or allowing for operating temperatures above 20 K. The high tolerance of RE-Ba 2 Cu 3 O 7− δ coated conductors to axial tensile and compressive strain has led to the concept of CORC ® cables in an attempt to develop a round and mechanically as well as electrically isotropic, high-performance conductor that would meet these challenging requirements. This review article will outline how CORC ® cables evolved from a concept into a practical and robust conductor for high-field magnets and compact superconducting power cables. This review article provides an extensive overview of how CORC ® cable technology has overcome most of the challenges associated with its use in large magnets for fusion, particle accelerators and in helium gas cooled power and fault current limiting cables, while further development is ongoing that will push the CORC ® cable technology to even higher performance levels.

27 May 2012 in Nature Materials
Verified
Journal Article
Closed access
PDF file
JWJ. D. Weiss
J. D. Weiss
CTC. Tarantini
C. Tarantini
JJJ. Jiang
J. Jiang
FKF. Kametani
F. Kametani
APA. A. Polyanskii
A. A. Polyanskii
EHE. E. Hellstrom
E. E. Hellstrom

2 November 2016 in Superconductor Science and Technology
Verified
Journal Article
Open access
PDF file
JWJeremy D Weiss
Jeremy D Weiss
TMTim Mulder
Tim Mulder
HKHerman J Ten Kate
Herman J Ten Kate
DLDanko C van der Laan
Danko C van der Laan
Conductor on Round Core (CORC ® ) technology has achieved a long sought-after benchmark by enabling the production of round, multifilament, (RE)Ba 2 Ca 3 O 7− x coated conductors with practical current densities for use in magnets and power applications. Recent progress, including the demonstration of engineering current density beyond 300 Amm −2 at 4.2 K and 20 T, indicates that CORC ® cables are a viable conductor for next generation high field magnets. Tapes with 30 μ m substrate thickness and tape widths down to 2 mm have improved the capabilities of CORC ® technology by allowing the production of CORC ® wires as thin as 3 mm in diameter with the potential to enhance the engineering current density further. An important benefit of the thin CORC ® wires is their improved flexibility compared to thicker (7–8 mm diameter) CORC ® cables. Critical current measurements were carried out on tapes extracted from CORC ® wires made using 2 and 3 mm wide tape after bending the wires to various diameters from 10 to 3.5 cm. These thin wires are highly flexible and retain close to 90% of their original critical current even after bending to a diameter of 3.5 cm. A small 5-turn solenoid was constructed and measured as a function of applied magnetic field, exhibiting an engineering current density of 233 Amm −2 at 4.2 K and 10 T. CORC ® wires thus form an attractive solution for applications between 4.2 and 77 K, including high-field magnets that require high current densities with small bending diameters, benefiting from a ready-to-use form (similar to NbTi and contrary to Nb 3 Sn wires) that does not require additional processing following coil construction.

28 February 2010 in Nature Materials
Verified
Journal Article
Closed access
PDF file
SLSanghan Lee
Sanghan Lee
JJJ. Jiang
J. Jiang
YZY. Zhang
Y. Zhang
CBChung Wung Bark
Chung Wung Bark
JWJ. D. Weiss
J. D. Weiss
CEC. B. Eom
C. B. Eom

5 October 2018 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
VAV A Anvar
V A Anvar
KIKiril Ilin
Kiril Ilin
KYKonstantin A Yagotintsev
Konstantin A Yagotintsev
BMBinet Monachan
Binet Monachan
KAK B Ashok
K B Ashok
BABalan K Ashok
Balan K Ashok
A conductor on round core (CORC ® ) cable is composed of several layers of helically wound high-temperature superconducting (HTS) tapes on a round core with the winding direction reversed in each successive layer. The cable is flexible but the flexibility is limited by the critical strain value causing breakage of the HTS layer when this strain level is exceeded. The cables for magnets in fusion reactors experience large mechanical and electromagnetic loads. These loads arise from the cabling, coil manufacturing, cooling, and magnet operation. In order to optimize the manufacture and operating conditions, the mechanical behavior of CORC ® cables must be understood for the different relevant loading conditions. The cable configuration with many contact interactions between tapes and the non-linear behavior of the materials during the production and operating conditions makes the modeling challenging. Detailed finite element (FE) modeling is required to account for these complexities. The FE modeling allows an accurate calculation of the stress–strain state (SSS) of the cable components under various loads and avoids time-consuming large-scale experimental optimization studies. This work presents a detailed FE modeling of the 3D SSS in a CORC ® wire under bending load. The elastic–plastic properties of the individual tape composite materials and its temperature dependence are taken into account. The FE model is experimentally validated by a multilayer CORC ® bending test performed by Advanced Conductor Technologies LLC. A critical intrinsic tensile strain value of 0.45% is taken as the threshold where the individual tape performance becomes irreversibly degraded. The proposed FE model describes the bending test of the CORC ® wire adequately and thus can be used to study other types of loads. A parametric study is ongoing with dependent variables to pursue a further optimization of CORC ® cables and wires for various applications.