Introduction: Conventional direct and indirect bonding techniques fail to obtain the ideal bracket position. Objective: To compare the accuracy of virtual and conventional direct bonding of orthodontic accessories. Methods: A single virtual configuration (dental mannequin with Class I malocclusion) served as basis for generating the reference model (treated virtually) and the intervention models (10 digital models and 10 solid models, obtained by means of prototyping). A total of 560 teeth were then equally distributed between a group of orthodontists (Group I, direct bonding; and Group II, virtual bonding), working in two different time intervals. The individual positions of the accessories were measured after three-dimensional superimposition with customized software. The Student’s-t test for paired samples, and Chi-square tests were used for statistical analysis, both at the level of significance of 5%. Results: In comparison of the errors in raw values, there were significant differences only in the vertical (p< 0.001) and horizontal dimensions (p< 0.001). Considering the groups of ranges by clinical limits of the deviations, these differences were significant in the three dimensions, vertical (p< 0.001), horizontal (p= 0.044) and angular (p= 0.044). Conclusion: Virtual bonding made it possible to obtain more precise/accurate positioning of the orthodontic accessories. The potential accuracy of this method brings new perspectives to refining the indirect bonding protocols.
Purpose To compare the maximum anterior and posterior tongue pressure, tongue endurance, and lip pressure in Class I, II, and III malocclusions and different facial types. Methods A cross-sectional observational analytical study was carried out in 55 individuals (29 men and 26 women) aged between 18 and 55 years. The participants were divided into groups according to Angle malocclusion (Class I, II, and III) and facial type. The maximum anterior and posterior tongue pressure, tongue endurance, and maximum lip pressure were measured using the IOPI (Iowa Oral Performance Instrument). To determine the facial type, the cephalometric analysis was accomplished using Ricketts VERT analysis as a reference. Results There was no statistically significant difference when comparing the maximum pressure of the anterior and posterior regions of the tongue, the maximum pressure of the lips, or the endurance of the tongue in the different Angle malocclusion types. Maximum posterior tongue pressure was lower in vertical individuals than in mesofacial individuals. Conclusion Tongue and lips pressure, as well as tongue endurance in adults was not associated with the type of malocclusion. However, there is an association between facial type and the posterior pressure of the tongue.
1 October 2005 in Revista Dental Press de Ortodontia e Ortopedia Facial
O laser vem sendo amplamente utilizado na área da saúde, encontrando-se em franca evolução na Odontologia, beneficiando o paciente com tratamentos atraumáticos, sem dor, com melhor pós-operatório, entre muitas outras vantagens. A Ortodontia também tem muito a ganhar com a utilização da luz laser, apesar de suas aplicações e seus efeitos não se encontrarem bem difundidos entre os profissionais. O presente trabalho objetivou realizar uma revisão na literatura a fim de elucidar o ortodontista sobre como ele poderá se beneficiar desta forma de energia, elevando a qualidade do seu trabalho e melhorando as condições do tratamento tanto para o profissional como para o paciente.
1 January 2021 in RGO - Revista Gaúcha de Odontologia
Digital smile design is an important tool for esthetic planning in dentistry as it facilitates ease of communication between professionals and patients. This clinical report has the objective of describing a clinical procedure involving digital smile design for the placement of porcelain laminate veneer restorations. The digital smile design included dental and facial analyzes. The smile curve was drawn and a dental ruler was used to delimitate the spaces between each tooth. An approximate simulation of the smile was generated using Adobe Photoshop software. For esthetic and functional evaluation of the digital plan was created a diagnostic waxing and mock-up. The laminate veneers were made with feldspathic porcelain. Digital smile design was essential for successful planning because it enabled better patient contact with the end result. This case demonstrates the importance of this tool in esthetic dentistry.
1 February 2019 in Dental Press Journal of Orthodontics
Introduction: The heat treatment of stainless steel wires is a routine clinical procedure adopted by many dentists in order to relieve the stress caused after performing bends in the archwire. Objective: This study aimed to evaluate the influence of heat treatment of stainless steel archwires with a rectangular section of 0.016 x 0.022’-in. Methods: For analysis of the dimensional stability, the anterior and posterior dimensions of forty 0.016 x 0.022-in stainless steel orthodontic archwires without heat treatment and 30 days after heat treatment were evaluated. For analysis of the mechanical properties, 12 stainless steel wire segments with the same rectangular section without heat treatment and 30 days after heat treatment were tested through tensile strength and strain tests. To evaluate if there were differences between the anterior and posterior dimensions, the results were analyzed by the Student’s t-test. To compare the tensile strength and strain between the groups, the ANOVA test was used. The level of significance adopted was 95% (p< 0.05). Results: The heat treatment did not stop the expansion of archwires 30 days after their preparation, and there was no statistical difference in the tensile strength and strain tests with and without heat treatment. Conclusion: From the findings of this study, it can be conclude that the mechanical behavior of heat-treated stainless steel archwires is similar to that of archwires not subjected to heat treatment.
The aim of this study was to assess the biosafety practices adopted during the COVID-19 pandemic that persisted in post-pandemic orthodontic clinical routines. In this cross-sectional study, 722 Brazilian orthodontists who were in the early phase of the pandemic, and 203 from the later phase, respectively, answered a 45-item questionnaire addressing basic personal information, use of personal protective equipment, biosafety protocols, and COVID-19 incidence. Descriptive statistics and chi-square tests were used to analyze the data. Most participants were infected with the coronavirus (from 10.1% to 65%). While 52.4% perceived providing care as very risky during the pandemic, this perception shifted to decreased to a moderate level of risk in the late phase of the pandemic (40.4%). The use of protective face masks/face shields decreased from 51.7% to 25.1%, as well as the use of disposable coats (from 77.1% to 45.8%). Many orthodontists discontinued the use of PFF2/N95 masks and reverted to wearing surgical masks again. Most orthodontists disinfected orthodontic bands, and photographic retractors through manual washing and autoclaving. Most participants preferred to clean their orthodontic pliers with 70% alcohol. A decline in orthodontists’ concern about biosafety during clinical appointments was observed in the late phase of the pandemic. Moreover, the need for greater specific care still persists, especially regarding the proper use of disposable coats, face shields, and surgical masks.