1 November 2008 in Atmospheric Environment
1 December 2011 in Atmospheric Environment
1 February 2007 in Energy & Fuels
11 May 2021 in Journal of Geophysical Research: Atmospheres
The absorption Ångström exponent (AAE) describes the spectral dependence of light absorption by aerosols. AAE is typically used to differentiate between different aerosol types for example., black carbon, brown carbon, and dust particles. In this study, the variation of AAE was investigated mainly in fresh aerosol emissions from different fuel and combustion types, including emissions from ships, buses, coal‐fired power plants, and residential wood burning. The results were assembled to provide a compendium of AAE values from different emission sources. A dual‐spot aethalometer (AE33) was used in all measurements to obtain the light absorption coefficients at seven wavelengths (370–950 nm). AAE470/950 varied greatly between the different emission sources, ranging from −0.2 ± 0.7 to 3.0 ± 0.8. The correlation between the AAE470/950 and AAE370‐950 results was good (R2 = 0.95) and the mean bias error between these was 0.02. In the ship engine exhaust emissions, the highest AAE470/950 values (up to 2.0 ± 0.1) were observed when high sulfur content heavy fuel oil was used, whereas low sulfur content fuels had the lowest AAE470/950 (0.9–1.1). In the diesel bus exhaust emissions, AAE470/950 increased in the order of acceleration (0.8 ± 0.1), deceleration (1.1 ± 0.1), and steady driving (1.2 ± 0.1). In the coal‐fired power plant emissions, the variation of AAE470/950 was substantial (from −0.1 ± 2.1 to 0.9 ± 1.6) due to the differences in the fuels and flue gas cleaning conditions. Fresh wood‐burning derived aerosols had AAE470/950 from 1.1 ± 0.1 (modern masonry heater) to 1.4 ± 0.1 (pellet boiler), lower than typically associated with wood burning, while the burn cycle phase affected AAE variation.
29 October 2009 in Toxicological Sciences
The importance of nanotechnologies and engineered nanoparticles has grown rapidly. It is therefore crucial to acquire up-to-date knowledge of the possible harmful health effects of these materials. Since a multitude of different types of nanosized titanium dioxide (TiO2) particles are used in industry, we explored their inflammatory potential using mouse and cell models. BALB/c mice were exposed by inhalation for 2 h, 2 h on 4 consecutive days, or 2 h on 4 consecutive days for 4 weeks to several commercial TiO2 nanoparticles, SiO2 nanoparticles, and to nanosized TiO2 generated in a gas-to-particle conversion process at 10 mg/m3. In addition, effects of in vitro exposure of human macrophages and fibroblasts (MRC-9) to the different particles were assessed. SiO2-coated rutile TiO2 nanoparticles (cnTiO2) was the only sample tested that elicited clear-cut pulmonary neutrophilia. Uncoated rutile and anatase as well as nanosized SiO2 did not induce significant inflammation. Pulmonary neutrophilia was accompanied by increased expression of tumor necrosis factor-alpha (TNF-α) and neutrophil-attracting chemokine CXCL1 in the lung tissue. TiO2 particles accumulated almost exclusively in the alveolar macrophages. In vitro exposure of murine and human macrophages to cnTiO2 elicited significant induction of TNF-α and neutrophil-attracting chemokines. Stimulation of human fibroblasts with cnTiO2-activated macrophage supernatant induced high expression of neutrophil-attracting chemokines, CXCL1 and CXCL8. Interestingly, the level of lung inflammation could not be explained by the surface area of the particles, their primary or agglomerate particle size, or radical formation capacity but is rather explained by the surface coating. Our findings emphasize that it is vitally important to take into account in the risk assessment that alterations of nanoparticles, e.g., by surface coating, may drastically change their toxicological potential.