In this study, nano zero-valent iron-reduced graphene oxide (NZVI-rGO) composites were synthesized to remove 2,4-dichlorophenol (2,4-DCP) as an efficient adsorbent. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) indicated that NZVI particles were successfully loaded and dispersed uniformly on rGO nanosheets. Fourier transform infrared spectroscopy (FTIR) analysis showed that the interaction between NZVI-rGO and 2,4-DCP promoted the adsorption process. A three-level, four-factor Box-Behnken design (BBD) of the response surface methodology (RSM) was used to optimize the influencing factors including NZVI-rGO dosage, 2,4-DCP initial concentration, reaction time and initial pH. A statistically significant, well-fitting quadratic regression model was successfully constructed to predict 2,4-DCP removal rate. The high value (15.95), very low value (<0.0001), nonsignificant lack of fit, and appropriate coefficient of determination ( ) demonstrate a good correlation between the experimental and predicted values of the proposed model. The analyses of variance reveal that NZVI-rGO dosage and reaction time have a positive effect on 2,4-DCP removal, whereas the increase of contaminant concentration and initial pH inhibit the removal, whereas the effect of contaminant concentration and initial pH is in reverse, where the change of NZVI-rGO dosage has the greatest effect. The optimum condition is1.215 g/L of NZVI-rGO dosage, 20.856 mg/L of 2,4-DCP concentration, 4.115 of pH, and 8.157 min of reaction time. It is verified by parallel experiments under the optimum condition, achieving the removal efficiency of100%.
Chitosan-stabilized nano zero-valent iron (CTS-nZVI) prepared by the liquid-phase reduction method has been shown to achieve a good dispersion effect. However, there has been little analysis on the mechanism affecting its stability and transport in saturated porous media. In this paper, settling experiments were conducted to study the stabilization of CTS-nZVI. The transport of CTS-nZVI in saturated porous media at different influencing factors was studied by sand column experiments. The stability mechanism of CTS-nZVI was analyzed from the point of view of colloidal stability by settling experiments and a zeta potential test. The theoretical model of colloidal filtration was applied for the calculation of transport coefficients on the basis of the column experiments data. Considering attachment–detachment effects, a particle transport model was built using HYDRUS-1D software to analyze the transport and spatial distribution of CTS-nZVI in a sand column.
Nanoscale zero-valent iron (NZVI) is a material that is extensively applied for water pollution treatment, but its poor dispersibility, easy oxidation, and inconvenient collection limit its application. To overcome these drawbacks and limit secondary contamination of nanomaterials, we confine NZVI supported by reduced graphene oxide (rGO) in the scaffold of sodium alginate (SA) gel beads (SA/NZVI-rGO). Scanning electron microscopy showed that the NZVI was uniformly dispersed in the gel beads. Fourier transform infrared spectroscopy demonstrated that the hydrogen bonding and conjugation between SA and rGO allowed the NZVI-rGO to be successfully embedded in SA. Furthermore, the mechanical strength, swelling resistance, and Cr(VI) removal capacity of SA/NZVI-rGO were enhanced by optimizing the ratio of NZVI and rGO. Interestingly, cation exchange may drive Cr(VI) removal above 82% over a wide pH range. In the complex environment of actual Cr(VI) wastewater, Cr(VI) removal efficiency still reached 70.25%. Pseudo-first-order kinetics and Langmuir adsorption isotherm are preferred to explain the removal process. The mechanism of Cr(VI) removal by SA/NZVI-rGO is dominated by reduction and adsorption. The sustainable removal of Cr(VI) by packed columns could be well fitted by the Thomas, Adams–Bohart, and Yoon–Nelson models, and importantly, the gel beads maintained integrity during the prolonged removal. These results will contribute significant insights into the practical application of SA/NZVI-rGO beads for the Cr(VI) removal in aqueous environments.
The study of the co-transport of Cr(VI) and microplastics (MPs) in porous media is important for predicting migration behavior and for achieving pollution removal in natural soils and groundwater. In this work, the effect of MPs on Cr(VI) migration in saturated porous media was investigated at different ionic strengths (ISs) and pHs. The results showed that pH 7 and low IS (5 mM), respectively, promoted the movement of Cr(VI), which was further promoted by the presence of MPs. The Derjaguin–Landau–Verwey–Overbeek (DLVO) results showed that the repulsive energy barrier between MPs and quartz sand decreased with increasing IS and decreasing pH, respectively, which promoted the retention of MPs in quartz sand and constrained the competition of Cr(VI) for adsorption sites on the surface of the quartz sand, thus facilitating the enhanced migration of Cr(VI), while Cr(VI) behaved conversely. Sodium alginate/nano zero-valent iron-reduced graphene oxide (SA/NZVI-rGO) gel beads could achieve the removal of MPs through a π-π interaction, hydrogen bonding, and electrostatic attraction, but the MPs removal would be reduced by 40% due to the competitive adsorption of Cr(VI). Notably, 97% Cr(VI) removal could still be achieved by the gel beads in the presence of MPs. Therefore, the gel beads can be used as a permeation reaction barrier to inhibit the MP-induced high migration of Cr(VI). The Cr(VI) breakthrough curves in reactive migration were well-fitted with the two-site chemical nonequilibrium model. Overall, the findings of this work contribute to the understanding of the migration behavior of Cr(VI) and MPs in saturated porous media and provide a theoretical basis for the remediation of soils and groundwater contaminated with Cr(VI) and MPs.
Cr(VI) pollution in water bodies is very harmful to human health and the environment. Therefore, it is necessary to remove Cr(VI) from water. In this study, the composite (FP-nZVI) was prepared by loading nano-zero-valent iron (nZVI) onto cellulose filter paper (FP) using a liquid-phase reduction method to improve the dispersibility and oxidation resistance of nZVI. In batch experiments, the effects of iron loading of FP-nZVI, initial concentration of Cr(VI), temperature, and pH on Cr(VI) removal were particularly investigated. The maximum removal rate of 98.6% was achieved at 25 °C, pH = 5, initial concentration of Cr(VI) of 20 mg/L, and FeCl3·6H2O solution concentration of 0.8 mol/L. The removal of Cr(VI) by FP-nZVI conformed to a pseudo-second-order kinetic model and Langmuir isotherm model. The mechanism of Cr(VI) removal was a multi-step removal mechanism, involving adsorption, reduction, and coprecipitation. Column experiments investigated the effect of flow rate (1 mL/min, 3 mL/min, and 5 mL/min) on Cr(VI) removal. We found that increasing flow rate slightly decreased the removal rate of Cr(VI). The transport of Cr(VI) in composite porous media was simulated using HYDRUS-1D, and the results show that the two-site model can well simulate the reactive transport of Cr(VI). This study may provide a useful reference for the remediation of groundwater contaminated with Cr(VI) or other similar heavy metals using FP-nZVI.
In this study, inexpensive, environmentally friendly, and biodegradable cellulose filter paper was used to load nano zero-valent iron (nZVI), effectively improving the dispersibility of nZVI and successfully preparing the supported modified cellulose filter paper (FP-nZVI). Subsequently, the capacity of FP-nZVI to remove Cr(VI) in a flow system was explored. FP-nZVI was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Traditional single-factor experiments often require a large number of repeated experiments when analyzing the interactions among multiple variables, resulting in a long experimental cycle and high consumption of experimental materials. This research used the Response Surface Methodology (RSM) based on the Box-Behnken Design (BBD) and the Artificial Neural Network (ANN) to optimize and predict the removal process of Cr(VI). This RSM investigated the interactions between the response variable (Cr(VI) removal rate) and the independent variables (Cr(VI) concentration, pH value, and flow rate). A highly significant quadratic regression model was constructed, which was proven by a high F value (93.92), an extremely low p-value (<0.0001), and a high determination coefficient (R2 = 0.9918). An ANN model was established to forecast the correlation between independent variables and the removal rate of Cr(VI). Both models demonstrate remarkable consistency with the experimental data; however, from the perspective of statistical parameters, the ANN model has more significant advantages; the coefficient of determination R2 reaches 0.9937, which is higher than that of RSM (0.9918); the values of indicators such as MSE, RMSE, MAE, MAPE, AAD, and SEP are all smaller than those of RSM. The ANN exhibits greater excellence in prediction error, value fluctuation, and closeness to the actual value and has a more excellent prediction ability. The experiment for treating Cr(VI) with FP-nZVI was optimized, achieving good results. Meanwhile, it also provides a valuable reference for similar experimental studies.