25 May 2022 in Neural Computing and Applications
13 November 2018 in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
In determination of flexible pavement layers moduli using Falling Weight Deflectometer (FWD), the pavement depth temperature should be determined and then the moduli should be corrected into a reference temperature. As direct measurement of pavement temperature is time consuming and is difficult to be determined in trafficked roads, some models are developed to predict temperature of asphalt layers through pavement depth, including BELLS model. The objective of this research is to determine correlation between actual measurement and prediction of temperature variations through asphalt layers with applying BELLS model. Ten new and rehabilitated pavement sites were selected in hot climate regions in Khuzestan and Kerman provinces in southern part of Iran. In typical hot summer days, pavement temperatures were measured at half and at one-third of the depth of asphalt layers and FWD testing were performed. Results indicated that a linear regression analysis of BELLS predicted temperatures versus measured values, provides very good correlation with actual field measurements of temperatures through the asphalt layers. Furthermore, predictions were more precise in rehabilitated pavements rather than in newly constructed pavements. Finally, using multi parametric linear fitting analysis, a new model was developed to accurately predict the temperature of asphalt layers in new pavements.
1 February 2023 in Journal of Materials in Civil Engineering
The main objective of this research is to develop a sustainable and environment-friendly asphalt binder based on the reutilization of waste engine oil (WEO) alongside crumb rubber (CR), two major waste materials of the automobile industry. This composite modification eliminates the limitations and the negative effects of solo application of these waste modifiers, including the poor workability and pumpability of the CR-modified binder, as well as compromised rutting resistance of the biobinder modified with WEO. Besides investigating the high-temperature properties of the composite-modified binder with CR and WEO, for the first time, a new method is presented to analyze the influence of the preparation parameters on the performance of the binder and optimize the whole production process. For this purpose, the design of experiment was conducted with the aid of the central composite design (CCD) method, and the rheological properties of the binders were evaluated by rotational viscosity (RV), dynamic shear rheometer (DSR), and multiple stress creep recovery (MSCR) tests. Based on the results of rotational viscosity at 135°C and the unaged and RTFO-aged rutting factor values at 58°C, regression models were established and analysis of variance was carried out on the preparation parameters. Overall, test results indicated that the addition of 5%–10% blending content of WEO in the composite-modified binder could achieve a satisfactory rutting resistance while improving its workability and pumpability. On the other hand, although the content of WEO had the most significant influence on the rheological properties of the binder samples, other parameters including preparation temperature and time also had influence to some extent. Additionally, optimum values of the preparation parameters were determined, and the production process was optimized.
27 September 2017 in Road Materials and Pavement Design
24 May 2017 in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
This paper presents a simple method to determine dynamic modulus master curve of asphalt layers by conducting Falling Weight Deflectometer (FWD) for use in mechanistic-empirical rehabilitation. Ten new and rehabilitated in-service asphalt pavements with different physical characteristics were selected in Khuzestan and Kerman provinces in south of Iran. FWD testing was conducted on these pavements and core samples were taken. Witczak prediction model was used to predict dynamic modulus master curves from mix volumetric properties as well as the bitumen viscosity characteristics. Adjustments were made using FWD results and the in-situ dynamic modulus master curves were obtained. In order to evaluate the efficiency of the proposed method, the results were compared with those obtained by using the developed procedure of the state-of-the-practice, Mechanistic-Empirical Pavement Design Guide (MEPDG). Results showed the proposed method has several advantages over MEPDG including: (1) simplicity in directly constructing in-situ dynamic modulus master curve; (2) developing in-situ master curve in the same trend with the main predicted one; (3) covering the large differences between in-situ and predicted master curve in high frequencies; and (4) the value obtained for the in-situ dynamic modulus is the same as the value measured by the FWD for a corresponding frequency.
1 February 2021 in Journal of Materials in Civil Engineering
Dynamic modulus of asphalt mixtures is one of the most important input parameters in design and rehabilitation of asphalt pavements. Dynamic modulus predictive models are alternative methods for laboratory determination of this parameter. These models were developed based on laboratory data. Due to sophisticated and laborious laboratory testing methods, there is a need to develop new models to determine dynamic moduli of in-service asphalt layers. In this study, nine different asphalt pavement sites were selected in two southern provinces of Iran. Falling weight deflectometer (FWD) testing was performed at each site and core samples were taken from the asphalt layers for volumetric analysis. Using the results, dynamic moduli of asphalt layers were determined using six predictive models, including Witczak, modified Witczak, Hirsch, Al-Khateeb, global, and simplified global models. Predicted dynamic moduli were compared with those determined from back-calculation analysis of FWD data. Existing predictive models were calibrated and new models were developed for the prediction of in situ dynamic modulus of asphalt layers in hot climate areas. Performance evaluation and validation of the new models showed high prediction accuracy and low prediction bias with very good correlations between the predicted and back-calculated values ( ).