Chan Mi Song

Chan Mi Song

Auto-generated profile, based on publicly available information

Chan Mi Song

Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 February 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
HKHyungmo Koo
Hyungmo Koo
JBJongseok Bae
Jongseok Bae
WCWoojin Choi
Woojin Choi
HOHansik Oh
Hansik Oh
HLHong Jun Lim
Hong Jun Lim
YYYoungoo Yang
Youngoo Yang
The retroreflective method has been used as a radio—frequency (RF) beamforming method for massive antenna array, for wireless communication systems, radars, and microwave power transfer (MPT) systems. In particular, the retroreflective method is suitable for optimum beamforming for both near—and far—field zones. Each transmitter (Tx) and receiver (Rx) circuit in the Tx array has its own phase offset, which should be calibrated for optimum retroreflective operation. This paper presents a simple and effective phase offset calibration method for the retroreflective beamforming arrays using a one—by—one basis optimum phase searching method with a receiver at a reference point. To verify the proposed method for a massive retroreflective array, a 5.2 GHz short— and mid—range (~ 4 m) MPT system, including a Tx array based on 8x8 antennas and an Rx using 6 antennas (5 rectennas for power reception, and 1 additional for pilot transmission) for charging mobile handsets was implemented. Optimal retroreflective beamforming from the Tx array, which was calibrated using the proposed method, was experimentally verified for angles of within ±45° degrees for both xz— and yz—planes. The implemented Tx and Rx circuits achieved a received dc power of about 100 mW at a distance of 4 m.

24 May 2021 in IEEE Access
Verified
Journal Article
Open access
CSChan Mi Song
Chan Mi Song
STSon Trinh-Van
Son Trinh-Van
SYSang-Hwa Yi
Sang-Hwa Yi
JBJongseok Bae
Jongseok Bae
YYYoungoo Yang
Youngoo Yang
KHKeum Cheol Hwang
Keum Cheol Hwang
In this paper, a method for calculating the received power in a radio-frequency wireless power transfer system with array antennas is proposed. The received power is derived based on the superposition of the electric fields that radiate from individual transmitter (Tx) elements and are captured by each receiver (Rx) element. That is expressed in a finite series form with the radiation patterns of an element considering mutual coupling in the array and corresponding distances between the elements of Tx and Rx. Unlike conventional methods (such as the Friis and Goubau formulas), this approach is able to calculate the received power precisely in both Fresnel and far-field regions. It is also efficiently applicable to various cases, such as those involving beamforming and with varying positions of Rx. The calculated results using this method are applied to a 5.2 GHz WPT system with array antennas and verified through comparisons with both simulation and experimental results.

13 April 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
SKSeok Kim
Seok Kim
CSChan-Mi Song
Chan-Mi Song
SLSeung-Hun Lee
Seung-Hun Lee
SSSung-Chan Song
Sung-Chan Song
Hyun-Ung OhHyun-Ung Oh
Hyun-Ung Oh
The small synthetic aperture radar (SAR) technology experimental project (S-STEP) mission aims to develop an innovative spaceborne SAR microsatellite as a constellation of 32 microsatellites featuring a high-resolution stripmap mode of 1 m. The S-STEP is a spaceborne SAR microsatellite technology demonstration program in which innovative approaches have been proposed and investigated for SAR payload system designs for improving the development speed, affordability, size and weight parameters, and quality of SAR satellite systems. In this study, the major design approach includes a bus–payload integrated flat-panel-type SAR payload based on an active phased-array antenna. This study conducted an SAR image performance analysis considering the mission requirements to validate the feasibility of the innovative SAR payload design of the S-STEP. These performance analysis results are presented to demonstrate the effectiveness of the proposed SAR payload design approach under the new space paradigm.

26 October 2020 in IEEE Access
Verified
Journal Article
Open access
JBJongseok Bae
Jongseok Bae
SYSang-Hwa Yi
Sang-Hwa Yi
HKHyungmo Koo
Hyungmo Koo
SOSungjae Oh
Sungjae Oh
HOHansik Oh
Hansik Oh
YYYoungoo Yang
Youngoo Yang
This paper presents a look-up table (LUT)-based focal beamforming system that can effectively transmit RF power up to mid-range distances (≤ 3 m) including when the Rx is in the near-field zones. The Tx elements control and radiate signals for the Rx even at the near-field zone ensuring the received signals are in-phase. Since the proposed system uses a LUT for storing the phase sets of the signals for the Tx elements, it requires only very simple hardware and a very simple adaptive control algorithm compared to conventional retroreflective method. In order to track the moving Rx, a 2-D adaptive sequential searching algorithm is proposed. The system can find the optimum phase set by sequentially searching the phase sets for a pre-determined 2-D area. The LUT of the phase sets are generated using geometric analysis over the entire 2-D area where the Rx could be located. To verify the proposed method, a 5.2 GHz mid-range (≤ 3 m) MPT system composed of a $4\times 8$ Tx array and a $2\times 3$ Rx array was designed and implemented. Using the proposed 2-D adaptive sequential searching algorithm, the optimum phase set for focal beamforming can be quickly found for a given position of the Rx. In our experiments, the results showed an RF power level of 177.8 mW was received at the Rx with a distance of 1 m with a total radiated RF power of 16W. Since the measured received power levels for various Rx positions agree well with the simulation results, the proposed system was proved to be an excellent candidate for the practical application.

8 July 2021 in IEEE Access
Verified
Journal Article
Open access
JWJeong Min Woo
Jeong Min Woo
WLWonseob Lim
Wonseob Lim
JBJongseok Bae
Jongseok Bae
CSChan Mi Song
Chan Mi Song
KLKyoung-Joo Lee
Kyoung-Joo Lee
YYYoungoo Yang
Youngoo Yang
In this study, a rectenna is adopted in a microwave-based wireless power transfer system to rectify the received radio frequency (RF) to DC power. Each rectenna comprises a DC-DC converter at the DC output port to ensure a stable power supply and a Schottky diode for the DC-combining network. The results indicate that the RF-DC conversion efficiencies of the rectifier circuit and 4×1 rectenna were 71% and 71.2% when the unit-cell RF input levels were 19 dBm and 19.6 dBm, respectively. Furthermore, the DC output levels of a 4×8 rectenna with and without the DC-DC converter were 28 V and 30 V, respectively, when the unit-cell RF input level was 20.2 dBm. Additionally, the RF-DC conversion efficiencies were 52.6% and 59.9% with and without the DC-DC converter, respectively. Thus, we experimentally verified that the Schottky diode combined with the DC-DC converter at the DC output port can increase the DC power combining level, making it suitable as an extendable array rectenna system.

13 May 2021 in IEEE Access
Verified
Journal Article
Open access
JSJaekyung Shin
Jaekyung Shin
JBJongseok Bae
Jongseok Bae
HKHyungmo Koo
Hyungmo Koo
SBSOON CHEOL BAE
SOON CHEOL BAE
Jongyun NaJongyun Na
Jongyun Na
YYYoungoo Yang
Youngoo Yang
The microwave power transfer (MPT) system requires a massive Tx array for building a focused radio wave to efficiently transfer power to the Rx. Beamforming IC is one of the core elements for the massive Tx array. This paper presents a 5.8 GHz 4-channel beamforming Tx IC based on a CMOS process. The beamforming Tx IC includes a resistive 4-way power splitter, 5-bit differential phase shifters, drive amplifiers, and power amplifiers. Each channel is designed to transmit a power of no less than 100mW. To verify the Tx IC, a 16-channel beamforming Tx module based on 16 patch antennas and four 4-channel Tx ICs was designed. The module also includes a PLL, a frequency doubler, and a 4-way Wilkinson power divider. MPT experiments to verify the beamforming IC and module were carried out using the implemented 16-channel Tx module at 5.8 GHz. Received power levels of 13 dBm and 2.1 dBm were achieved at distances of 0.4 and 1.4 m, respectively. The results are almost similar to the values acquired from the calculation using the Friis equation.