High Strength Low Alloy steels (HSLA) for oil and gas pipelines should display high mechanical strength, toughness, ductility and weldability. In this work we studied the influence of quenching and tempering temperature on the yield strength, ultimate tensile strength, percent elongation and hardness of API 5L steel pipes in order to optimize heat treatments to be performed after hot induction bending of the material. The thermal cycles involved soaking temperatures of 880, 920 and 960 °C, cooling water at 15, 23 and 31 °C and tempering at 530, 600 and 670 °C. From this, experimental design techniques were used to reduce the number of experiments. The results from contour maps suggest that soaking temperatures of 910 and 950 °C and tempering between 540 and 610 °C were the most suitable for treatment, regarding mechanical strength. The variation of the water temperature was not significant for the assumed cooling conditions. The prediction regression models of the mechanical properties from the variables involved in the heat treatments showed a good fit between the experimental and predicted results, with correlation coefficient between 0.89 and 0.94.
RESUMO Nos últimos anos, vários estudos foram realizados buscando reduzir o peso de veículos automotores, a fim de diminuir as emissões de poluentes. Neste cenário os aços de baixa densidade do sistema Fe-Mn-Al-C podem ser considerados uma alternativa promissora para suprir essas exigências da indústria automotiva. Geralmente, nos aços de baixa densidade, uma quantidade considerável de alumínio é adicionada a fim de reduzir a densidade geral do aço. No entanto, altos teores de alumínio promovem características distintas na microestrutura, destes aços quando comparados aos aços convencionais, como a presença do carboneto k ((Fe, Mn)3AlC), além da necessidade de se entender a combinação deste elemento com outros elementos de liga que podem ser adicionados. Neste contexto, este trabalho tem como objetivo avaliar a microestrutura, a dureza e a densidade resultantes em função da influência do Al e do Nb em uma nova composição química pertencente ao sistema Fe-Mn-Al-C, na condição trabalhada a quente, a partir de análises de difração de raios X, microscopia eletrônica, medidas de dureza e densidade por princípio de Arquimedes. Os resultados permitiram indicar que o alto teor de Al adicionado promoveu uma redução de cerca de 13% na densidade, em relação aos aços estruturais tradicionais, e a estabilidade da ferrita δ até a temperatura ambiente. A condição avaliada apresentou a temperatura ambiente uma microestrutura formada por uma matriz de ferrita δ e α, juntamente com precipitados de carboneto k (AlFe3C) e carboneto de nióbio (NbC), estes dois últimos devido as adições de Al e Nb, resultando em uma dureza de 59,4 ± 1 HRA e uma estimativa do limite de resistência a tração de próximo a 800 MPa – dentro da faixa dos aços avançados de alta resistência (Advanced High Strenght Steels – AHSS).
An experimental study on the distribution of residual stresses induced by shot peening on samples of SAE 1020 steel with pre-existing compressive stresses is presented. Two samples with similar geometries were subjected to a heat treatment to relieve stress. Then, one of the samples was subjected to a cementation process to introduce compressive residual stresses. Both samples, with and without cementation, were subjected to the same shot peening treatment. Using X-ray diffraction and electrolytic polishing to remove superficial layers, the depth-resolved residual stress distribution was obtained. It was concluded that the effect of pre-existing compressive stresses should be considered as a factor that influences the final distribution of the residual stresses induced by shot peening, namely the maximum of shot peening induced residual stresses moves closer to the surface in a sample with large initial compressive stresses and its value is greater than the maximum value for a specimen with lower initial compressive stresses.