Stormwater is recognised as a vector for microplastics (MPs), including tyre wear particles (TWPs) from land-based sources to receiving waterbodies. Before reaching the waterbodies, the stormwater may be treated. In this study, sediments from six treatment facilities (five retention ponds and a subsurface sedimentation tank) were analysed to understand MP occurrence, concentrations, sizes, polymer types and distribution between inlet and outlet. The concentrations of MPs showed large variations between and within different facilities with MP concentrations of 1,440–72,209 items/kg (analysed by μFTIR) corresponding to 120–2,950 μg/kg and TWP concentrations from <DL up to 69,300 μg/kg (analysed by pyrolysis–GC–MS), with significantly higher concentrations at the inlet compared to the outlet. Polypropylene (PP) was the predominant MP type in terms of number in all samples. TWPs were dominant by mass in most (nine) samples. The relatively low density of PP polymers implies that density might not be the sole factor influencing particle settlement behaviour. Small particles occurred more frequently than large ones; around 70% of the particles detected in the samples were 100 μm or smaller. In summary, this study highlights the occurrence of MPs, including TWPs, in stormwater facilities and demonstrates variations in concentrations depending on sites and locations within the facility.
The effect of chemical cleaning and regular backwashing on the efficiency of an ultrafiltration membrane fouled during stormwater treatment was studied. Increasing backwash time from 30 to 60 s resulted in an increase in productivity by 20%. However, the productivity was highest when a backwash time of 45 s was used (3% higher than using 60 s). Chemical cleaning was carried out using an alkaline solution (NaOH with or without NaOCl) followed by acid washing with HCl. The addition of NaOCl to the cleaning chemical did not significantly increase the efficiency of chemical cleaning, and the average pure water permeability increase was 97 ± 13 LMH bar−1 after chemical cleaning with NaOH followed by HCl and 117 ± 15 LMH bar−1 after chemical cleaning with NaOH + NaOCl followed by HCl, on average. In addition, reversibility after chemical cleaning was 96 ± 67%, on average. The result from scanning electron microscopy showed that at the end of the experiments, inorganic foulants existed in both the inner layer (feed side) and the outer layer (permeate side) of the membrane.
Blue-green infrastructure (BGI) options are considered to be more sustainable practices for water management and bring a range of benefits over and above water management. Davidshall in Malmö, Sweden, has been used as a case area to assess the multiple benefits of implementing BGI, considering seven alternative BGI schemes systematically developed along two scales: naturalness (i.e. more/less engineered/complex) and spatial distribution (e.g. decentral vs. end-of-pipe). The baseline alternative was the existing situation. The Benefit Estimation Tool (B£ST) was used to carry out a socio-economic assessment. The overall benefits varied significantly (two orders of magnitude), depending on the BGI scheme implemented: the greatest values were associated with natural decentral, natural decentral/end-of-pipe, and engineered decentral/end-of-pipe alternatives, those including sub-surface and open dry detention, stormwater tree pits, and rain gardens. The three B£ST categories providing the greatest benefits were enhancing amenity, benefiting health, and reducing flooding. Cultural ecosystem services were provided by all alternatives, and two alternatives (natural decentral and natural decentral/end-of-pipe) also provided regulating ecosystem services. The study showed that amenity and health were the most significant benefits of BGI implementation, contrasting with the main aim of BGI implementation, which was stormwater management (water quality and flood protection).
In this study, the spatial relationship between critical pipes identified using edge-based centrality measures and pipes with higher failure probability-based on selected vulnerability indicators were analysed in sanitary sewer networks. By analysing two sub-networks, one residential and the other a central network, significant spatial associations between pipes with high centrality values and those exhibiting adverse conditions (poor CCTV grades, previous blockages, and low self-cleaning capabilities) were identified. Path-based centrality measures, particularly edge betweenness and K-path edge centrality were less influenced by weights when identifying critical pipes. In contrast, non-path-based measures like nearest neighbour edge centrality could identify more localised critical pipes within the sewer networks investigated. The results showed that the spatial patterns between critical pipes and pipes in adverse conditions were not random and could support proactive maintenance planning and the development of more resilient networks. Additionally, the impact of network structure, connectivity, and differences in the composition of pipe attributes could contribute to variations in the strength of observable spatial associations.
Enhancing sediment accumulation monitoring techniques in sewers will enable a better understanding of the build-up processes to develop improved cleaning strategies. Thermal sensors provide a solution to sediment depth estimation by passively monitoring temperature fluctuations in the wastewater and sediment beds, which allows evaluation of the heat-transfer processes in sewer pipes. This study analyses the influence of the flow conditions on heat-transfer processes at the water–sediment interface during dry weather flow conditions. For this purpose, an experimental campaign was performed by establishing different flow, temperature patterns, and sediment depth conditions in an annular flume, which ensured steady flow and room-temperature conditions. Numerical simulations were also performed to assess the impact of flow conditions on the relationships between sediment depth and harmonic parameters derived from wastewater and sediment-bed temperature patterns. Results show that heat transfer between water and sediment occurred instantaneously for velocities greater than 0.1 m/s, and that sediment depth estimations using temperature-based systems were barely sensitive to velocities between 0.1 and 0.4 m/s. A depth estimation accuracy of ±7 mm was achieved. This confirms the ability of using temperature sensors to monitor sediment build-up in sewers under dry weather conditions, without the need for flow monitoring.
A polymeric ultrafiltration (UF) membrane was used for stormwater treatment, with the focus on evaluating the increase in the membrane process productivity by adding pulsatile fluid flow to UF membrane treatment. Sedimentation and sieving were used as pre-treatment. The result showed that increasing the pulse frequency from 0 to 4 Hz increased productivity from −6.6 to 82 LMH. UF membrane removed suspended solids, oil and turbidity below detection limit. The UF membrane also separated total coliforms, E. coli and P. aeruginosa below detection limit. Total organic carbon (TOC) was reduced by between 81%, in average. In addition, the UF membrane was able to reduce BOD7 and COD to below 7 mg/L in the permeate. According to the US EPA, WHO, and national regulations in Canada, Japan, and South Korea, treated stormwater can be used for flushing toilets and streets irrigation and agricultural use.