5 December 2022 in Optics Letters
We designed and tested a distributed acoustic sensing (DAS) that co-exists with optical communication over a two-mode fiber (TMF). In particular, we excited both linearly polarized (LP) modes, LP01 and LP11a, using a photonic lantern for simultaneous information signal transmission while collecting the backscattered Rayleigh light at the near end of the fiber to detect vibrations from a predetermined source. While transmitting data using on–off keying (OOK) or orthogonal frequency-division multiplexing (OFDM) modulation schemes, the optical fiber DAS offers high signal-to-noise ratio (SNR) values that are always larger than the minimum acceptable 2 dB SNR. In addition, as a proof-of-concept experiment, we report parallel sensing and OFDM transmission achieving a data rate of up to 4.2 Gb/s with a bit error rate (BER) of 3.2 × 10−3.
20 May 2024 in Journal of Lightwave Technology
Optical sensing and communication systems are essential for various applications in terrestrial, space, and submarine environments. However, integrating these systems poses several challenges, especially in terms of energy sustainability and management. In this work, we report on energy harvesting over fiber (EHoF) using amplified spontaneous emission (ASE) from erbium-doped fiber amplifiers (EDFAs). We demonstrate that the transmitted ASE power that is wasted in fiber Bragg grating (FBG) sensors and the ASE noise that is filtered out in optical communication systems can be harnessed for EHoF. We present a multi-functional system that includes EHoF, FBG-based sensing, fiber-optic communication, and underwater optical wireless communication (UOWC), and discuss the performance metrics of the different modules. This multi-functional system successfully harvests 6.12 mW of electrical power while enabling up to 2.5 Gbps of hybrid optical fiber and UOWC data communication with simultaneous temperature sensing using FBG in an underwater environment.
24 May 2024 in IEEE Access
Pipeline networks are the most reliable and efficient means of transporting oil, gas, and fluids across extensive distances. Therefore, monitoring pipelines continuously and ensuring their correct operation is essential. In this work, we investigated the capability of Fiber Bragg grating (FBG) in monitoring localized and uniform metal loss produced inside pipelines repaired with composite sleeves. We performed numerical simulations using finite element method (FEM) to characterize the hoop strain of different wrapped pipeline structures, including those with glass fiber reinforced polymer (GFRP) and with carbon fiber reinforced polymer (CFRP) sleeves. Besides, we investigated the strain at various locations, including the pipe wall’s outer surface and the sleeve’s external surface. The numerical results demonstrate that the hoop strain produced by internal pressure can be transmitted to the top surface of the composite sleeve, and its magnitude increases under the presence of metal loss. Furthermore, we corroborated these numerical results by conducting experiment tests using two pipe sections repaired with 7 mm-GFRP and 6 mm-CFRP composite sleeves and an array of FBGs to monitor the hoop strain variation on the steel pipe and the sleeves in response to applied strain at areas affected by metal loss with various depth sizes. The experimental results show that the minimum detectable metal loss thickness are 0.832 mm using FBG on the steel pipe and 1.04 mm using FBG on 7 mm-GFRP sleeve, and 0.2 mm using FBG on the steel pipe and 0.429 mm using FBG on a 6 mm-CFRP sleeve, considering an internal pressure of ~1800 psi, and the case where the FBG is at the location of the metal loss defect. The obtained results prove that this non-destructive and non-intrusive approach harnessing FBG sensors placed on the composite sleeve effectively monitors the internal metal loss and ensures the continuous inspection of pipeline integrity.
1 January 2025 in Advanced Devices & Instrumentation
Optical fibers, the backbone of global transoceanic communications infrastructure, have the potential to support distributed acoustic sensing (DAS) enhanced by pattern recognition algorithms for oceanic soundscape monitoring and animal conservation. This work enhances subsea telecommunication single-mode fibers (SMFs) by using wavelength division multiplexing (WDM) to concurrently transmit communication and DAS signals. We identified orthogonal frequency division multiplexing (OFDM) as the optimal modulation scheme, minimizing interference between DAS and communications. OFDM achieved a signal-to-noise ratio (SNR) of 10.71 dB for DAS, compared to 8.76 dB for on-off keying (OOK), and enabled a data rate of 7.59 Gbps with a bit error rate (BER) of 2.93 × 10 −3 over 1 km of SMF. The system, tested in a water tank with marine animal sounds, achieved over 90% classification accuracy when integrated with a convolutional neural network (CNN), and maintained 85% accuracy in real-world conditions in the Red Sea. These results demonstrate the potential for enhanced oceanic monitoring without the need for installing new subsea monitoring tools.
14 July 2023 in IEEE Photonics Technology Letters
Distributed fiber-optic sensors (DFOS) have been widely deployed in a wide range of applications. The operational principle of such DFOS typically relies on monitoring light backscattered due to pumping optical pulses in an optical fiber. Once the DFOS’ optical pump pulses reach the distal end of the optical fiber, the power carried by each pulse is conventionally wasted and dissipated to the medium surrounding the fiber without a benefit. Here, we report on energy harvesting from the DFOS’ optical pulses to recycle the wasted optical power for electric-consuming devices supply. We demonstrated the feasibility of this concept by harvesting energy from a fiber-optic distributed acoustic sensor (DAS) and a distributed temperature sensor (DTS). The study further investigates the impact of changing the pulse repetition rate within the 5–25 kHz range on the harvested power. Without any disturbances in the DFOS functionalities, power values of up to 0.871 mW were harvested as a proof-of-concept demonstration.
13 December 2024 in IEEE Sensors Journal
Metallic pipelines are essential in the oil and gas industry. Hence, various technologies have been developed to monitor their integrity, particularly in diagnosing corrosion-induced metal loss. Once a fault is detected, the structure is reinforced with a composite sleeve as a provisional measurement to extend the lifespan of the asset before replacement. However, these temporary solutions significantly hinder the ability of conventional monitoring technologies to track the progression of metal loss. Their inherent characteristics, such as high-vibration insulation, reduce the effectiveness of traditional sensors. To address these limitations, we report on the use of fiber-optic Distributed Acoustic Sensing (DAS) integrated with machine-learning algorithms. This approach facilitates the creation of a novel distributed monitoring tool capable of accurately detecting and tracking post-repair metal loss. The proposed approach collects temporal and spectral data from operational sounds along an optical fiber wound around the pipeline while a machine-learning algorithm classifies these signals as indicating intact or faulty operation in unrepaired sections and quantifies the damage progression of repaired sections, providing a comprehensive solution for timely detection, repair, and replacement decisions. As a proof-of-concept demonstration, we induced artificial sounds generated from numerical simulations in real repaired and unrepaired sections of a metallic pipe, mimicking those produced by fluid flow in pipelines under different metal loss etching depths. The system captured samples of these sounds to train and test the performance of convolutional neural network (CNN) models, achieving fault detection accuracy of up to 99.93% and post-repair metal loss quantification accuracy exceeding 85%.