23 December 2024 in The Journal of Physical Chemistry C
Cu-doped LaCu x Mn1-x O3 perovskites have been used as a model system for a joint experimental and theoretical assessment of the influence of the Cu doping level on the structural, electronic, and magnetic properties. The different Cu-doped phases LaCu0.3Mn0.7O3 (LCM37), LaCu0.5Mn0.5O3 (LCM55), and LaCu0.7Mn0.3O3 (LCM73) including the respective Cu- and Mn-free benchmark materials La2CuO4 (LC) and LaMnO3 (LM) have been studied by magnetization measurements and electronic paramagnetic resonance. Ferromagnetic behavior was detected for pure LM and all Cu-doped perovskites, whereas antiferromagnetic behavior was revealed for La2CuO4. Generally, an increased antiferromagnetic contribution was shown for higher Cu doping levels. Equally, magnetization was highlighted to decrease with increasing Cu content. Sophisticated hybrid density functional theory calculations of the electronic and magnetic properties using defect-free, idealized Cu-doped model structures agree well with the experimental results. The findings reveal that copper incorporation influences both the electronic conductivity and the magnetic properties. Notably, the materials exhibit a tunable degree of half-metallicity and significant electronic spin polarization, establishing them as promising candidates for advanced technological applications in spintronics and catalysis. The insights gained from this study contribute to a broader understanding of perovskite materials and their versatile applications.
2 March 2026 in Journal of the American Chemical Society
Using aberration-corrected electron microscopy and spectroscopy, we reveal the atomic scale structure and catalytic function of the A-site-deficient perovskite La0.7Fe0.7Mn0.3O3, uncovering a heterogeneous defect landscape that governs its activity in reducing NO by CO. We identified a layer of La0.7-xFe0.7Mn0.3O3 that is highly A-site-deficient. This layer is just two to three unit cells thick at the surfaces and the interfaces of the perovskite particles and transitions toward the bulk into stoichiometric LaFe0.7Mn0.3O3. These confined defect layers stabilize catalytically active sites, enabling the formation of FeOx inclusions ranging from approximately 1 nm to several nanometers in size at the surfaces. In situ surface characterization and catalytic measurements reveal that these interfacial FeOx nanoparticles serve as active sites during the NO reduction by CO via the Mars-van Krevelen mechanism. Our findings establish a direct relationship between the structure and properties of nanoscale A-site nonstoichiometry and redox-driven catalytic activity. This relationship offers a new design strategy for tailoring reactivity through defect engineering.
29 April 2026 in ACS Catalysis
In situ diffuse reflectance IR spectroscopy (DRIFTS) demonstrates that the lack of suitable CO adsorption sites on LaCu0.5Mn0.5O3 (LCM55) perovskites limits the overall NO + CO reaction. Metallic Cu and vacancy sites (or cationic sites near these vacancies) can both act as active sites for CO adsorption. We provide evidence that adsorbed nitrogen atoms facilitate CO adsorption and conversion at vacancy sites formed under strongly reducing conditions. The proposed mechanism involves the reaction of adsorbed CO with surface nitrogen species to surface isocyanate (NCO) species (represented by a peak at 2170 cm−1 at 600 °C). Subsequently, CO spills from N sites to active reduced sites. This channel of localized CO adsorption increases the reactive sticking coefficient of CO at or next to active centers and indirectly supports the presence of atomically dispersed sites. CO adsorption via this mechanism is especially important for the reaction progress at higher temperatures, where the relatively weak CO adsorption on metallic Cu centers is a limiting factor. In due course, the involvement of nitrogen atoms in the CO adsorption pathway suppresses N2O formation and enhances selectivity toward N2.
6 November 2025 in ACS Applied Nano Materials
We studied the effect of Ti substitution on nickel B-sites in LaNiO3 to unravel the influence of Ti doping on structural stability, Ni exsolution, and methane dry reforming (DRM) properties. Ni can be substituted by Ti down to compositions of xNi = 0.25 without compromising both phase and structure purity. At even higher Ti doping levels, formation of the pyrochlore-type La2Ti2O7 phase occurs. Ti substitution has a significant influence on the stability under reducing conditions and the appearance of specific intermediate structures relevant for DRM operation. Full decomposition is only observed for LaNiO3 and the xNi = 0.75 sample, which yield the La2O3 phase relevant for DRM activity at low Ti doping levels. A common impurity phase between xNi = 0.75 and 0.25 is La2TiO5, which acts as a Ti and La sink and hinders the formation of La2O3. For higher Ti doping levels, hydrogen reduction increases the amount of La2Ti2O7. A common denominator of all samples after hydrogen reduction is the full leaching of all nominally available Ni from the perovskite. The self-activation properties during DRM operation strongly depend on the Ti substitution level. Self-activation with either full or partial decomposition is only possible for LaNiO3 and xNi = 0.75, where intermediate lanthanum oxycarbonate formation occurs. For xNi = 0.50, the remaining perovskite structure is stable, but Ni exsolution nevertheless occurs, triggering DRM activity. Successive Ti doping invokes a change in the DRM mechanism from oxycarbonate-based at low Ti amounts (LaNiO3 and xNi = 0.75) to a more reactive-oxygendominated one for samples xNi ≤ 0.50, as indicated by X-ray photoelectron spectra. Ti doping also allows to economize the amount of Ni for DRM applications it can be lowered to a quarter of the initial amount referenced to pure LaNiO3 without compromising DRM activity.