30 November 2018 in IOP Conference Series: Materials Science and Engineering
1 January 2025 in Journal of Thermal Engineering
This study examines factors associated with the cavities formed in 3D-printed porous thermoplastics, and establishes their relationship with the thermal conductivity of bulk material. The research has examined two porous thermoplastics, specifically poly-lactic acid (PLA) and acrylonitrile butadiene styrene (ABS). Certain categories have been used for the cavities based on their shapes (sphere, cube and diamond), sizes (0.5 to 1.9 mm), numbers (200 to 500), and distributions (in-line or staggered). Specific findings indicate that the optimal thermal conductivity value can be achieved by utilizing samples with 500 pores of 1.5 mm pore diameter. It is shown, the pores could be in the shape of diamonds and distributed in a staggered manner in order to have minimum thermal conductivity. The thermal conductivity values for the most favorable specimens were determined to be 0.13 W/m·K for PLA and 0.12 W/m·K for ABS. The observed values demonstrate a decrease of 40-45% in comparison to the non-porous samples of the same materials.
1 September 2024 in Baghdad Science Journal
في هذه الدراسة ، تم تطبيق تقنية الصب بالتحريك (SCT) لتكوين مركب الألمنيوم (Al) النانوي مع نسب وزنية مختلفة من مسحوق ثاني أكسيد التيتانيوم النانوي (TiO2). تم فحص الخصائص البنائية ,الميكانيكية والتآكل لمتراكبات النانو. دراسة البنية المجهرية تمت عن طريق المجهر الإلكتروني الماسح (SEM) ، بينما تم الحصول على التركيب البلوري للعينات باستخدام حيود الأشعة السينية (XRD). بالإضافة إلى ذلك ، تم غمر المركبات النانوية في محلول 0.5 مولاري من حمض الهيدروكلوريك لقياسات معدل التآكل والديناميكية الفعالة. أظهرت النتائج أن أفضل عينة كانت 0.03٪ ، حيث زادت الصلابة بنسبة 23٪ ، لكن قوة الشد زادت إلى 52٪. حيث أظهرت صور SEM للعينات المعززة بالجسيمات النانوية تجانسًا وانتشارًا واضحًا للجسيمات النانوية في المصفوفة. لذلك ، فإن إضافة جزيئات TiO2 النانوية إلى معدن الألمنيوم أدى إلى تحسين صلابة وقوة الشد للمركبات النانوية بشكل ملحوظ. بالمقابل أظهرت نتائج التآكل أن المواد المركبة النانوية لديها مقاومة تآكل أعلى من المواد المركبة القائمة على Al7075.
1 January 2026 in Mustansiriyah Journal of Materials Engineering and Sustainability
Additional manufacturing technology has been used by using the laser bracket manufacturing method for the purpose of producing various geometric components. This method is characterized by many advantages and also there is a structure that can be described in low and these materials are characterized by highly controlled synthetic synthesis and are characterized by accurate engineering and featuring high deposition rates. It was noted that this method is of a complex nature where this method contains changes in structural and controlled parameters that mechanical, thermal and chemical behavior is affected by those variables. Studies on laser-based additive manufacturing show that improved mechanical properties—such as hardness, fracture resistance, yield strength, and ultimate tensile strength—are closely linked to microstructural advancements. As well because of exact control produces accurate structures, which are affected by microscopic substances. This exact control results in reduced structural contrast and improving granular size as well as improving morphological characteristics. For the purpose of improving the quality of the surface and significantly reducing the article, it has used an advanced technique for predicting the subsequent layer. In addition, interconnection between sedimentary layers may improve and this leads to treatment for conventional metals.