Hayrettin Düzcükoğlu

Hayrettin Düzcükoğlu

Auto-generated profile, based on publicly available information

Hayrettin Düzcükoğlu

Selcuk University

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2017 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
MEMürsel Ekrem
Mürsel Ekrem
HDHayrettin Düzcükoğlu
Hayrettin Düzcükoğlu
MŞMuhammet Ali Şenyurt
Muhammet Ali Şenyurt
ÖŞÖmer Sinan Şahin
Ömer Sinan Şahin
AAAhmet Avcı
Ahmet Avcı
In this study, the effects of addition of boron nitride nanoplatelets (BNNPs) upon friction and wear behavior of epoxy resin have been investigated by using pin-on-disk test. It has been reported in the literature that certain amounts of BNNP addition can be useful for enhancement of mechanical properties. Therefore, it is very important to obtain the effect of such addition upon friction and wear performance of epoxy resin. BNNPs have been incorporated at 0.3–0.5–0.7–1 wt %. It is shown that BNNP addition results in decrease in friction coefficient and wear. It is also shown that the best results are obtained with 0.5% nanoplatelet addition. It is also observed that heat conduction of epoxy resin is enhanced by the nanoplatelet addition.

8 October 2010 in Journal of Failure Analysis and Prevention
Verified
Journal Article
Closed access
PDF file
HDHayrettin Düzcükoğlu
Hayrettin Düzcükoğlu
RYRifat Yakut
Rifat Yakut
EUEyyub Uysal
Eyyub Uysal

1 January 2015 in International Journal of Materials, Mechanics and Manufacturing
Verified
Journal Article
Closed access
HDHayrettin Düzcükoğlu
Hayrettin Düzcükoğlu
SÇSelman Çetintürk
Selman Çetintürk

4 July 2024 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
HDHayrettin Duzcukoglu
Hayrettin Duzcukoglu
HKHalil Burak Kaybal
Halil Burak Kaybal
RARamazan Asmatulu
Ramazan Asmatulu

11 April 2024 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
RYRifat Yakut
Rifat Yakut
HDH. Düzcükoğlu
H. Düzcükoğlu
HAharun akkuş
harun akkuş
Polymer gears are often used in power transmission due to their numerous advantages. Heat accumulates on polymer gears during operation. Over time, this accumulated heat leads to damage; and shortens the service life of the gears. To prevent this, various fillers are added to the polymer materials. These fillers help to dissipate the heat generated on the gears. In this study, 25% glass fibers, 35% carbon powder, and 60% bronze particles were added to the polytetrafluoroethylene (PTFE) matrix to determine the wear behavior of gears. The properties of the matrix and the filler mainly influence the wear behavior of PTFE composites. The study showed that all composite gears with filler have better wear resistance than pure PTFE gears due to their better thermal stability. After the tests, it was found that the gears made of PTFE + 35% carbon additive had about 12 times better wear rates than those made of pure PTFE. Based on the average temperature values of the experiment, it was found that the mass temperature of gears made of 35% carbon-doped PTFE is about 38-39% lower than that of pure PTFE. This study contributes to the standard studies on heat build-up, thermal damage, and wear of gears made of polymers with different fillers and ratios.

29 June 2026 in International Journal of Damage Mechanics
Verified
Journal Article
Open access
BÜBayram Ünal
Bayram Ünal
Yasin UslugilYasin Uslugil
Yasin Uslugil
Hasan ULUSHasan ULUS
Hasan ULUS
MEMürsel Ekrem
Mürsel Ekrem
HDHayrettin Düzcükoğlu
Hayrettin Düzcükoğlu
This study reports the synthesis of multilayer Ti 3 C 2 T x MXene through selective etching of Ti 3 AlC 2 and its incorporation into Elium ® thermoplastic resin at loadings of 0.25–1.0 wt.%. The resulting nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction, thermogravimetric analysis/differential scanning calorimetry, and mechanical tests, including tensile (ASTM D638), flexural (ASTM D790), and fracture toughness (ASTM D5045) analyses. The 0.75 wt.% MXene composite exhibited the most balanced performance, achieving a tensile strength of 69.45 MPa, a flexural strength of 110 MPa, and a 31% improvement in fracture toughness over neat Elium ® . These enhancements were attributed to uniform nanofiller dispersion and effective interfacial interaction that facilitates stress transfer and crack deflection. SEM fractography revealed a transition from smooth, brittle fracture surfaces in the neat matrix to rough, branched crack paths in the MXene-filled composites, indicating improved energy dissipation. Overall, MXene/Elium ® nanocomposites showed superior strength, toughness, and thermal stability, highlighting their potential as lightweight and recyclable materials for structural applications in automotive, aerospace, and protective sectors.