1 February 2022 in IEEE Transactions on Industrial Electronics
Zero voltage switching (ZVS) control is an effective and promising way to further improve the power density, efficiency and electromagnetic interference for the two paralleled silicon carbide inverters with coupled inductors. In this article, focusing on the popular 180 o interleaved pulsewidth modulation (PWM), the circulating current ripple prediction model is first derived as a function of operating conditions in the time-domain. With the assistance of this model, the actual trajectory of phase-leg currents can be reconstructed by superposition of sampling fundamental current and predicted circulating current ripple, without adding any high-frequency current sensor or auxiliary circuit. By carefully considering the ZVS requirement of all switches, a variable switching frequency PWM (VSFPWM) for full range ZVS control is proposed in this article. The proposed VSFPWM shows a good performance of ZVS realization in various load situations, as well as a good dynamic response of the inverter during current step change. In addition, due to the real-time variation of switching frequency, the proposed VSFPWM demonstrates the obvious advantage in conductive EMI reduction. Both the simulation and experimental results are presented to verify the effectiveness of the analysis and proposed method.
28 July 2023 in IEEE Transactions on Industrial Electronics
Pulsewidth modulation inverter driven motor will suffer from common-mode (CM) voltage, which will not only cause electromagnetic interference to the system, but also cause CM leakage current to damage the motor bearings. Driven by a two-level voltage-source inverter), the dual three-phase motor (DTPM) system with even numbers of phase-legs provides an opportunity to cancel the CM voltage actively. This article proposes a CMV suppression method that can be applied to DTPMs with arbitrary angle displacement (AD). Based on the principle of space vector modulation, this method uses four effective zero common-mode voltage vectors to synthesize the reference voltage, and uses virtual-voltage vectors (VVs) to simplify the synthesis process. While suppressing the CMV, the vector assignment also takes into account the harmonic suppression of the system. The suggested method can achieve the elimination of CMV for DTPM with arbitrary AD, and can improve the maximum modulation ratio of the system. The maximum modulation ratios for 30° and 60° are 1.035 and 1.154, respectively. Therefore, the proposed method has certain practicality. Finally, the CM voltage suppression method is verified on a 12-slot/10-pole permanent magnet synchronous motor with different angle displacements (ADs).
14 November 2022 in IEEE Transactions on Transportation Electrification
For railway traction application by induction motor drives, common-mode (CM) leakage current generated by traction inverter is a big threat. This paper introduces the technology of paralleled inverters to drive double dual-three-phase induction motors for traction application. The pulse width modulation (PWM) in the paralleled inverters can eliminate the CM voltage caused by PWM of the inverters and to mitigate the CM leakage current in the dual motors. The design and analysis of the dual-three-phase induction machine is introduced at first. Through different terminal connections, dual three-phase motors can be connected in the same phase and in the reverse phase. Then the paralleled inverters with zero CM PWM are used to drive the double motors in traction mode for both of the two kinds of windings. Considering the deadtime effect, the zero CM PWM for phase-reversed windings can obtain better CM elimination effect than the case with phase-aligned windings. At the same time, the ZCM algorithm can be well combined with synchronous modulation to meet the needs of the actual railway traction system. Simulation and experimental results are provided to validate that with the proposed method, common mode current of the double induction motors can be reduced significantly and the traction performance can be obtained.
29 April 2024 in IEEE Transactions on Transportation Electrification
Bearing current or common mode (CM) leakage current induced by high-frequency CM voltage have long posed challenges for AC motors fed by power electronics inverters. This paper focuses on the optimization of zero-CM PWM based on paralleled inverters, which can theoretically eliminate CM voltage. For the original zero-CM PWM method, it suffers from a significant issue related to circulating current asymmetry and current jumping problems. These issues amplify the peak value and the low-order harmonics of circulating current, which can significantly increase the design burden of coupled inductors. To address aforementioned challenges, this paper introduces an optimized zero-CM PWM strategy. During the two adjacent switching cycles, it leverages the freedom of vector time allocation in the first and second switching cycle. The volt-second balance can be achieved over two switching cycles, and the voltage vector sequence can be redistributed for the purpose of symmetry and suppression of circulating current. The proposed method not only maintains the CM voltage elimination, but also exhibits excellent circulating current suppression without any additional hardware cost. Finally, both theoretical analysis and experimental validation are presented to demonstrate the effectiveness of proposed method.
30 April 2025 in IEEE Transactions on Industrial Electronics
The article analyzes the common-mode (CM) electromagnetic interference (EMI) in four three-phase two-level inverter parallel (FTTIP) system and proposes a novel zero-CM voltage (ZCMV) modulation strategy by equivalently treating each phase as a five-level system. It also analyzes the impact of dead zone, using ZCMV with dead zone compensation and random variable dead zone (ZCMVCR) to further enhance the ultimate capability of active EMI suppression. It also maintains output voltage balance to improve overall system performance. Simulation and experimental verification are conducted. The experimental results show that compared to traditional space vector pulse width modulation (SVPWM), ZCMVCR can reduce CM EMI by 10–25 dB in the range of 10 kHz–3 MHz. The variable dead-zone method can further reduce the CM EMI by 5–10 dB in high frequency range of 1–3 MHz on the basis regular ZCMV.