Joining the laser welding club: Laser welding is an integral part of modern manufacturing, but it fractures ceramic materials. Penilla et al. developed two methods for welding ceramics using ultrafast lasers. One method tunes the ceramic properties, allowing the laser to transit through the ceramic and weld at the interface between pieces. The other method optimizes a gap between pieces to efficiently deposit energy. Both methods leverage short but energetic pulses to create a melt pool that allows ceramics to be joined, without the high temperature used for traditional ceramic welds. Science , this issue p. 803
We introduce high thermal conductivity aluminum nitride (AlN) as a transparent ceramic host for Ce3+, a well-known active ion dopant. We show that the Ce:AlN ceramics have overlapping photoluminescent (PL) emission peaks that cover almost the entire visible range resulting in a white appearance under 375 nm excitation without the need for color mixing. The PL is due to a combination of intrinsic AlN defect complexes and Ce3+ electronic transitions. Importantly, the peak intensities can be tuned by varying the Ce concentration and processing parameters, causing different shades of white light without the need for multiple phosphors or light sources. The Commission Internationale de l’Eclairage coordinates calculated from the measured spectra confirm white light emission. In addition, we demonstrate the viability of laser driven white light emission by coupling the Ce:AlN to a readily available frequency tripled Nd-YAG laser emitting at 355 nm. The high thermal conductivity of these ceramic down-converters holds significant promise for producing higher power white light sources than those available today.
Nitrogen‐rich titanium nitride (TiN) thin films containing excess nitrogen up to 87.0 at.% were produced on (100) Si substrates via the reactive magnetron DC‐sputtering of a commercially available 99.995 at.% pure Ti target within an argon‐nitrogen (Ar‐N2) atmosphere with a 20‐to‐1 gas ratio. The process pressure (PP) and substrate temperature (TS) at which deposition occurred were varied systematically between 0.26 Pa–1.60 Pa and between 15.0∘C–600∘C, respectively, and their effects on the chemical composition, surface morphology, and preferred orientation were characterized by energy dispersive X‐ray spectroscopy (EDS), field emission scanning electron microscopy (FE‐SEM), and X‐ray diffraction (XRD). The EDS analysis confirms increasing nitrogen content with increasing PP and TS. The SEM images reveal a uniform and crystallized surface morphology as well as a closely packed cross‐sectional morphology for all crystalline films and a loosely packed cross‐sectional morphology for amorphous films. Films produced at lower PP and TS have a pyramidal surface morphology which transitions to a columnar and stratified structure as PP and TS increase. The XRD analysis confirms the existence of only the δ‐TiN phase and the absence of other nitrides, oxides, and/or sillicides in all cases. It also indicates that at lower PP and TS, the preferred orientation relative to the substrate is along the (111) planes, and that it transitions to a random orientation along the (200), (220), and (311) planes as PP and TS increase and these results correlate with and qualify those observed by SEM.
Light scattering due to birefringence has prevented the use of polycrystalline ceramics with anisotropic optical properties in applications such as laser gain media. However, continued development of processing technology has allowed for very low porosity and fine grains, significantly improving transparency and is paving the way for polycrystalline ceramics to be used in demanding optical applications. We present a method for producing highly transparent Cr3+ doped Al2O3 (ruby) using current activated pressure assisted densification. The one-step doping/densification process produces fine grained ceramics with well integrated (doped) Cr, resulting in good absorption and emission. In order to explain the light transmission properties, we extend the analytical model based on the Rayleigh-Gans-Debye approximation that has been previously used for undoped alumina to include absorption. The model presented captures reflection, scattering, and absorption phenomena in the ceramics. Comparison with measured transmission confirms that the model adequately describes the properties of polycrystalline ruby. In addition the measured emission spectra and emission lifetime are found to be similar to single crystals, confirming the high optical quality of the ceramics.
1 August 2012 in Materials Science and Engineering: B