Saibin Han

Saibin Han

Auto-generated profile, based on publicly available information

Saibin Han


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 July 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
CSChuanwen Song
Chuanwen Song
WYWang Yingnan
Wang Yingnan
LLLi Lian
Li Lian
SHSaibin Han
Saibin Han
PZPengyang Zhang
Pengyang Zhang
XHXiufei Hu
Xiufei Hu
Submicrometer boron-doped diamond (BDD) epilayers with controlled thickness, smooth surfaces, and reliable boron incorporation are needed for high-power and radiation-hard electronics, yet these requirements are difficult to satisfy simultaneously. Here, finite-element simulations linked pit suppression to symmetric plasma fields and uniform H and CH3 distributions near the growth surface, guiding the design of a pocket-type molybdenum holder as well as optimization of gas composition and total flow rate. Further adjustment of the actual gas-phase ratios suppressed pits and reduced the surface roughness to Ra = 0.19 nm. Optical emission spectroscopy was used to stabilize the initial growth stage, where abrupt fluctuations in boron incorporation within the first 100 nm can easily occur. Introducing trimethylboron (TMB) in two steps with a 2 min interval improved boron incorporation uniformity. Under the optimized conditions, BDD epilayers with thicknesses of 300 nm - 1.5 μm were obtained. The 682 nm film showed a 004 rocking-curve FWHM of 91.98 arcsec and a sharp diamond Raman peak. SIMS gave a boron concentration of 6.6 × 1017 cm-3, while Hall measurements yielded a mobility of 111 cm2/(V·s), a carrier concentration of 3.66 × 1016 cm-3, and a resistivity of 1.53 Ω·cm. A preliminary vertical Au/P+-diamond/UID-diamond/P+-diamond/Au device also showed repeatable photoresponse from 0 to ±10 V.

2 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ZWZiang Wang
Ziang Wang
DLDengke Li
Dengke Li
YPYan Peng
Yan Peng
XHXiufei Hu
Xiufei Hu
XZXiaoyu Zhang
Xiaoyu Zhang
PCPeijian Chen
Peijian Chen
Understanding stress evolution in diamond/SiC heterostructures is critical for high-power electronic applications, yet the thickness-dependent stress transition and its thermal behavior remain underexplored. Here, a synergistic approach combining temperature-dependent Raman spectroscopy and finite element simulation to systematically investigate the stress evolution of diamond films (5–280 µm) on 4H-SiC substrates from 27 °C to 600 °C is adopted. A distinct tensile-to-compressive stress transition is observed within the critical thickness range of 100–200 µm. Thin films (5 µm and 100 µm) are dominated by tensile stress (e.g., D100 exhibits 0.50 GPa tensile stress at 27 °C), whereas thick films (200 µm and 280 µm) show compressive stress (e.g., D200 presents 0.23 GPa compressive stress). Raising the temperature to 600 °C relieves thermal stress, with reduction rates at the center and edge of the 280 µm-thick film reaching 45% and 86%, respectively. Spatial stress distribution reveals that center stress is higher than edge stress, with the difference widening with increasing temperature and film thickness. Films exhibit a stress-temperature trend of first increasing then decreasing, while the edge of the thickest film remains compressive across the entire range. FEM results agree well with thin-film experiments but show notable deviations for thick films. The optimal diamond/SiC thickness ratio is identified as 1:5–2:5, enabling low-stress diamond films by regulating the tensile-to-compressive stress transition. This work clarifies the stress evolution law of diamond/SiC heterostructures, and provides a practical design pathway towards low-stress, thickness-tailored diamond/SiC composites for next-generation high-power electronic and thermal management systems.