25 October 2018 in Tekhnichna Elektrodynamika
Joomla! - the dynamic portal engine and content management system
26 December 2020 in Microsystems, Electronics and Acoustics
Моделювання ґратчастого багатошарового екрану для зниження магнітного поля ліній електропередачі
29 April 2021 in Microsystems, Electronics and Acoustics
АДАндрій Віталійович Димерець
Андрій Віталійович Димерець
Overhead power lines are one of the largest sources of the low-frequency magnetic fields. Such magnetic fields occur the harmful effects on human health and other biological objects. The current size of the security zones doesn’t provide a safe level of the magnetic flux density outside them. Therefore, the task of reducing the magnetic flux density value of the overhead power lines outside the security zone is urgent. Some overhead power lines have sections where two lines pass parallel to each other at a short distance. For such lines the method of phase wires hanging order optimization can be applied. For efficiency comparison of different hanging orders was chose two types of electricity pylons: portal (PB330-7) and triangular (P330-3). The cases both lines done by the same pylons were investigated. Analyze of different hanging orders efficiency was performed by mathematical simulation using MATLAB software. The magnetic flux density computation inside the security zone and outside it was done by a specialized simplified methodology of power lines electric and magnetic fields calculation. It is shown that in case of identical phase wires hanging order and the same currents direction of two parallel lines there is a significant increasing of magnetic flux density value at the border of the security zone and outside it for both types of the electricity pylons. It is determined that with a certain hanging order it is possible to achieve a significant reduction of the magnetic flux density value. For lines with electricity pylons of a portal type (PB330-7) the most efficient is the mirror order. It allows to obtain a decreasing of magnetic flux density more than 30 percent at the security zone border and more than 50 percent outside it. For pylons of a triangle type (P330-3) the most efficient is the nonsymmetrical order. It provides the decreasing of magnetic flux density up to 20 percent. In case of opposite currents direction, the most efficient is the same hanging order for both types of electricity pylons. It is shown that optimal phase wires hanging order allows to decrease the magnetic flux density value outside the security zone border, to reduce the distance to border of the area with safe level of the magnetic flux density, to increase the phase current value at which the magnetic flux density value reaches the safe level within the security zone.
30 December 2024 in TECHNICAL SCIENCES AND TECHNOLOGIES
The relevance of the article is to highlight the process of creating a computer model of metal object detection in theCOMSOL Multiphysics environment and the results of its application. Its use will increase the efficiency of the use of induction metal detectors, which is extremely important under war conditions, as it will allow better and faster detection of metal explosive objects.One of the most common in terms of price/quality ratio for detecting metal objects is the single-circuit resonant inductivemetal detector, which has certain structural features. The ability to detect metal objects is provided by a system of inductioncoils, the most common of which is the Double D type system. The problem of calculating the induction of the magnetic fieldgenerated by a coil in any region (set of points) of space is therefore very complex and difficult to solve mathematically.Moreover, its complexity is directly proportional to the number of these points.The purpose of the article is to develop a computer model for the detection of metal objects for an inductive metal detectorwith a double D-coil system, to configure its parameters using the example of a real Fischer F5 metal detector, to analyse theresults of the application with the determination of the possible directions of use of the created model, as well as the features and limitations of its application.The article presents the results of creating a three-dimensional model of the metal object detection system, describes itsmain parameters, and lists the interfaces and tools used in the COMSOL environment. Graphs and colour maps show thedependence of the voltage induced in the receiver coil and the phase difference between the currents of the two coils on the position of a cylindrical metal target as it moves in the horizontal and vertical planes, as its geometric dimensions change and as its specific electrical conductivity changes (corresponding to the change in metal). The limits of the geometric dimensions and the distance of the target from the system where detection becomes unlikely are determined.The conclusions emphasise the significance of the results obtained, as well as possible directions for the application ofthe developed model and the benefits of its use.