There is a growing interest in 2D materials-based devices as the replacement for established materials, such as silicon and metal oxides in microelectronics and sensing, respectively.
Nitrogen-doped carbon sponge-type nanostructures (N-CSTNs) containing coaxial multiwalled carbon nanotubes are synthesized at 1020 °C by using a modified chemical vapor deposition (CVD) arrangement. Here, the CVD reactor is supplied by two flows coming from two independent sprayers (called sprayer A and sprayer B). The nebulized material in each sprayer is transported by two different gases with different flow velocities. The synthesis of carbon N-CSTNs is performed using different precursors: sprayer A contains a solution composed of ethanol, thiophene and ferrocene, whereas sprayer B contains a solution of benzylamine, thiophene and ferrocene. Samples are classified according to the position inside the reactor and characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and thermogravimetric analysis (TGA). Samples collected at the beginning of the reactor contain curly structures with diameters of 10–100 nm. At the end of the reactor, the sample is mainly formed by one type of structure. A spongy-type material is mainly formed in the hottest zone of the tubular furnace. The N-CSTNs are highly hydrophobic with oil sorption properties, which could be used for adsorption of oil spills.
This paper aims to improve the aqueous stability and electrochemical activity of HKUST-1 (or Cu3(BTC)2, BTC = benzene 1,3,5-tricarboxylate; and HKUST from Hong Kong University of Science and Technology) by the incorporation of Graphene Oxide (GO). The synthesis was carried out in two steps; first, CuII ions were pre-adsorbed on the surface of GO, and then the BTC organic linker was added to form the HKUST-1 structure dispersed on GO sheets. Two concentrations of copper were used in the synthesis, 3.57 and 14.27 mmol, to obtain the samples: GO@HKUST-1low and GO@HKUST-1high, respectively. N2 adsorption properties of GO@HKUST-1high suggest an increase in surface area compared to HKUST-1 up to 1082.0 m2·g−1. In addition, the CO2 capture of GO@HKUST-1high increased from 5.34 (HKUST-1) to 6.92 mmol·g−1 at 273 K and 100 kPa. This improvement is associated with the dispersion of the HKUST-1 on the GO sheets achieved through the synthesis strategy used, which also increased the surface area, H2O adsorption capacity of the composite material, and electrochemical stability. After the H2O adsorption tests, XRD confirmed that the material was stable under aqueous conditions, showing that the material did not undergo any structural modification.
We demonstrated that the ball-milled slag-SiC mixture is an effective catalyst to grow pyrrolic nitrogen-doped multiwall carbon nanotubes (N-MWCNTs) by aerosol assisted chemical vapor deposition (AACVD) method. N-MWCNTs synthesized at 800 °C, 850 °C and 900 °C were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, x-ray powder diffraction (XRD), and x-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). TEM characterizations revealed the presence of a bamboo-like structure, a typical feature of nitrogen-doped carbon nanotubes. The presence of nitrogen was confirmed by the N1s XPS spectrum. Furthermore, a deconvolution of the N1s spectra revealed the presence of N-pyrrolic defects. This nitrogen functionality is investigated concerning the presence of silicon carbide material. Giant nanotubes with large diameters were obtained when SiC was added to the slag to be used as a substrate for N-MWCNTs synthesis. From Raman spectroscopy, the appearance of the D-band was observed, indicating the presence of topological defects that were also observed by TEM. XRD and TEM characterizations demonstrated the presence of Fe3C and α-Fe nanoparticles. The N-MWCNTs fabricated here could be used into (electro)catalytic applications or for reinforcing ceramic nanomaterial or polymers.