13 August 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a high-efficiency neutralized continuous class-F (CCF) CMOS power amplifier (PA) design technique for millimeter-wave (mmW) 5G mobile communications. A parasitic-aware tuned-load with a high-order harmonic-resonance network is proposed to shape the current and voltage waveforms for the CCF PA. At mmW frequencies, the gate-drain capacitance (Cgd) creates adverse capacitive loading on harmonic-tuned output load networks. As a result, a CCF PA suffers from compromised power efficiency. To address this, we integrate a transformer with a tunable coupling coefficient between gate-drain of the power-device. This proposed technique allows accurate neutralization of Cgd, reducing detrimental loading effect on harmonic-tuned load while enhancing power efficiency and stability. We fabricated a CCF PA in 65-nm CMOS technology achieving >40% power-added efficiency (PAE) over 33.3% fractional bandwidth (25-35 GHz) and 46.4% peak PAE at 29 GHz. The measured peak saturated output power (Po,sat) is 14.8 dBm at 30 GHz. The PA is tested with 64-quadrature-amplitude-modulated signal at a data rate of 1.5 Gb/s. Under this test setup, the PA achieves modulated PAE of 26%/24%/21.4% and average output power (Po,avg) of 9.2/8.8/8.6 dBm at 28, 32, and 34 GHz, respectively, while maintaining better than -25 dB of error vector magnitude and -27 dBc of adjacent channel leakage ratio. To the authors' knowledge, this design presents one of the highest reported PAEs among mmW CMOS PAs.
3 October 2023 in IEEE Transactions on Microwave Theory and Techniques
This article presents a highly efficient GaN-based harmonic-tuned multiband RF rectifier for wireless power transfer (WPT) applications. The rectifier has been implemented by incorporating a microstrip coupler and a transmission line-based phase shifter to convert a power amplifier (PA) into a synchronous rectifier based on the time-reversal duality principle. The proposed rectifier provides a compact solution for wireless power charging systems while supporting dual-bands. The microstrip coupler is used to derive the gate driving signal for the device, which requires a weak coupling from the input RF signal. The coupler has been characterized separately for wideband operation from 1 to 3 GHz with only 0.3-dB insertion loss. Measurement results show that the rectifier has 77% and 75% efficiencies at 1.17 and 2.4 GHz, respectively, when the input RF power is 10 W. The rectifier shows $>$ 50% efficiency for input power levels down to 1.5 W. To the best of the authors’ knowledge, this rectifier presents one of the highest RF-to-dc rectification efficiencies in dual-band operation for a watt-level RF input power.
7 August 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
For the first time, this work presents a wireless-wireline hybrid 3D interconnect that employs orthogonal simultaneous bidirectional signaling for 3D Network-on-chip to achieve $2\times $ bandwidth density. We combine wireless near-field inductive coupling channel (NFIC) encompassing wireline through-silicon vias (TSV) to leverage orthogonal simultaneous bidirectional (SBD) signaling. This technique provides an efficient way of doubling interconnect bandwidth in the same area by means of passive wireless and wireline interconnects. The proposed hybrid 3D interconnect shows at least -70dB of NFIC-TSV isolation in the band of interest. We also present a comprehensive link analysis to derive the energy-area trade-off of an NFIC link and its fundamental performance limits. Further, we demonstrate on how equalization has the potential to decouple the fundamental energy-area tradeoff. The prototype transceiver measures a simultaneous bidirectional data and clock communication at an effective data rate of 6.6 Gb/s consuming 263 fJ/bit in 65 nm CMOS bulk process. The developed hybrid 3D interconnect architecture exhibits a $2\times $ improved link performance over state-of-the-art 3D simultaneous bidirectional links. A hybrid 3D Network-on-chip (3D NoC) implementation is demonstrated using the proposed hybrid interconnect technology and shows a 50% lower area and cost for the same energy-delay-product (EDP) over the conventional TSV based links.
3 July 2018 in IEEE Journal on Emerging and Selected Topics in Circuits and Systems
Large scale parallel implementation of matrix multiply and accumulate (MAC) core poses significant energy and area constraints in analog voltage domain under reduced supply voltage. A spatial multi-bit sub-1V time-domain matrix multiplier interface is presented using multi-bit back-gate-driven delay elements as a scalable alternative for various approximate computing applications. A single-chip solution is demonstrated for two application modes: a high throughput digitally-driven mode for acceleration and a low energy analog front-end mode for sensing. In accelerate-mode, the system achieves an aggregate throughput of 21.6 GMAC/s with 9 TOPS/W energy efficiency. In sense-mode, the system exhibits an energy efficiency of 55.3 TOPS/W for classification purpose. The proposed architecture utilizes 16-parallel 6-bit input vectors to perform matrix MAC computations using time-domain signal processing with 3-bit resistive weights at a sub-1V supply of 0.7 V. An integrated speculative time-to-digital converter (TDC) is employed for 6-bit time-domain quantization with an on-chip mismatch calibration scheme. The prototype is fabricated in 65 nm CMOS technology and occupies an active area of 0.04 mm2. The system performs image recognition of handwritten digits using a machine learning scheme and demonstrates an average classification accuracy of 84.3% on the MNIST dataset. The resultant energy per MAC computation in the proposed spatial architecture is about 15× lower than a digital CMOS combinational logic based parallel-tree MAC.
2 August 2018 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This paper presents an inductorless wideband gain-boosted baseband (BB) amplifier suitable for wireless network-on-chip (WiNoC) architectures. Current reuse active feedback (FB) and feed-forward (FF) techniques are proposed for extending bandwidth, increasing gain, and reducing power consumption and area overhead compared to traditional BB amplifiers. To maximize the benefits of the FB and FF amplifiers, a skewed differential topology is introduced, which reduces the impact of ringing in the amplifier’s step response, allowing greater design flexibility and improved performance. The amplifier is fabricated in 65-nm CMOS and achieves a bandwidth of 11 GHz with a small active area, 0.0029 mm 2 , due to the inductorless bandwidth-extension technique. The amplifier consumes 2.58 mW from a 1-V supply, suitable for a high-data-rate wireless receiver in power- and area-constrained WiNoC. With the proposed BB amplifier, a 60-GHz ON–OFF-keying (OOK) receiver for WiNoC is presented to demonstrate excellent energy efficiency and compact area. The wireless receiver demodulates 16-Gb/s OOK while consuming 16.3 mA with a small area overhead of 0.09 mm 2 . Based on the high bandwidth, low-power consumption, and small area overhead, to the best of the author’s knowledge, the amplifier achieves the best figure of merit among existing amplifiers in similar CMOS technology nodes.
5 September 2018 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Wireless interconnects using near-field inductive coupling (NFIC) enables contactless vertical communications necessary for the design of energy efficient and robust 3-D manycore systems. However, the achievable performance, energy efficiency, bandwidth, and associated area overhead of NFICs are intertwined imposing significant design challenges and tradeoffs to explore the optimum link configuration. To address these challenges, in this paper, we propose a holistic design approach for exploring energy-efficient NFICs and target to exploit the benefits of the NFICs in the context of efficient and reliable network-on-chip (NoC) design. The proposed design framework employs statistical link analysis to select optimum NFIC-link configuration and is significantly more efficient in terms of energy efficiency and area overhead compared to the state-of-the-art counterparts. We demonstrate that 3-D NoCs incorporating NFIC-enabled links outperform through-silicon-via (TSV) counterparts. In addition, the overall reliability of TSV- and NFIC-enabled hybrid 3-D NoC is significantly better than only TSV-based NoCs in order to counteract the electromigration and workload-induced stress challenges.