2 August 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper implements a wide aperture high-resolution true time delay for frequency-uniform beamforming gain in large-scale phased arrays. We propose a baseband discrete-time delay-compensating technique to augment the conventional phase-shift-based analog or hybrid beamformers. A generalized design methodology is first developed to compare delay-compensating analog or hybrid beamforming architecture with their digital counterpart for a given number of antenna elements, modulation bandwidth, ADC dynamic range, and delay resolution. This paper shows that delay-compensating analog or hybrid beamformers are more energy-efficient for high dynamic-range applications compared to true-time-delay digital beamformers. To demonstrate the feasibility of our proposed technique, a four-element analog delay-compensating baseband beamformer in 65-nm CMOS is prototyped. A time-interleaved switched-capacitor array implements the discrete-time delay-compensating beamformer with a wide delay range of 15-ns and 5-ps resolution. Measured power consumption is 47 mW with frequency-uniform array gain over 100-MHz modulated bandwidth, independent of angle of arrival. The proposed delay compensation scheme is scalable to accommodate the delay differences for large antenna arrays with higher range/resolution ENOB compared with prior art.
5 February 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
The best beam steering directions are estimated through beam training, which is one of the most important and challenging tasks in millimeter-wave and sub-terahertz communications. Novel array architectures and signal processing techniques are required to avoid prohibitive beam training overhead associated with large antenna arrays and narrow beams. In this work, we leverage recent developments in true-time-delay (TTD) arrays with large delay-bandwidth products to accelerate beam training using frequency-dependent probing beams. We propose and study two TTD architecture candidates, including analog and hybrid analog-digital arrays, that can facilitate beam training with only one wideband pilot. We also propose a suitable algorithm that requires a single pilot to achieve high-accuracy estimation of angle of arrival. The proposed array architectures are compared in terms of beam training requirements and performance, robustness to practical hardware impairments, and power consumption. The findings suggest that the analog and hybrid TTD arrays achieve a sub-degree beam alignment precision with 66% and 25% lower power consumption than a fully digital array, respectively. Our results yield important design trade-offs among the basic system parameters, power consumption, and accuracy of angle of arrival estimation in fast TTD beam training.
19 February 2018 in IEEE Transactions on Microwave Theory and Techniques
In this paper, a high-efficiency frequency-reconfigurable CMOS power amplifier (PA) design technique is presented at 24 and 28 GHz using integrated tunable neutralization and matching networks. To cope with the adverse effects of gate-drain capacitance (C gd ) in millimeter-wave (mm-wave) CMOS PAs in deep-submicrometer technologies, we propose a reconfigurable coupling-coefficient-based transformer. This technique provides optimum neutralization of C gd in a common-source configuration, while enabling tunable neutralization in a frequency reconfigurable PA. Furthermore, to reconfigure the PA's input and output matching networks, a low-loss frequency-reconfigurable matching topology using a switched substrate-shield inductor is proposed. The adopted matching network addresses the high loss in a conventional frequency reconfigurable matching approach, while facilitating high efficiency in the proposed PA design. Using the proposed techniques, a class-AB PA is fabricated in a 65-nm CMOS technology. This prototype achieves measured saturated power-added efficiency (PAE sat ) of 42.6%, saturated output power (P o,sat ) of 14.7 dBm at 24 GHz, and 40.1% PAE sat , and 14.4 dBm P o,sat at 28 GHz while occupying an active area of only 0.11 mm 2 . At 24 and 28 GHz, the PA is tested under 16 and 64-quadrature amplitude modulation (QAM) signals with 250 MHz of channel BW. The PA achieves modulated PAE of 15.2%/14.1%, error vector magnitude of -26.4/-26.6 dB, and adjacent channel leakage ratio of -30/-32 dBc at an average output power of 7.1/7 dBm for a 64-QAM signal with 250-MHz BW at 24 and 28 GHz, respectively. To the best of the author's knowledge, the design presents one of the highest PAEs among mm-wave CMOS PAs reported to date, while it also supports multiband operation.
27 March 2017 in IEEE Transactions on Microwave Theory and Techniques
A switched substrate-shield inductor (SSI) topology in bulk CMOS is proposed which minimizes parasitic capacitance and substrate losses, while tuned magnetically induced currents facilitate inductor tunability. The high frequency behavior of the induced current is analyzed, resulting in intuitive insights and design guidelines for a high-performance SSI. An SSI prototype in 65-nm bulk CMOS achieves 34% inductance tunability with a quality factor of >10.3. A voltage-controlled oscillator (VCO) using SSI achieves 40.3% tuning range, from 21 to 31.6 GHz, and a phase noise of -119.1 ± 3.7 dBc/Hz at 10-MHz offset frequencies. The VCO core consumes 4.3 ± 0.2 mW from a 1-V supply.
13 August 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a high-efficiency neutralized continuous class-F (CCF) CMOS power amplifier (PA) design technique for millimeter-wave (mmW) 5G mobile communications. A parasitic-aware tuned-load with a high-order harmonic-resonance network is proposed to shape the current and voltage waveforms for the CCF PA. At mmW frequencies, the gate-drain capacitance (Cgd) creates adverse capacitive loading on harmonic-tuned output load networks. As a result, a CCF PA suffers from compromised power efficiency. To address this, we integrate a transformer with a tunable coupling coefficient between gate-drain of the power-device. This proposed technique allows accurate neutralization of Cgd, reducing detrimental loading effect on harmonic-tuned load while enhancing power efficiency and stability. We fabricated a CCF PA in 65-nm CMOS technology achieving >40% power-added efficiency (PAE) over 33.3% fractional bandwidth (25-35 GHz) and 46.4% peak PAE at 29 GHz. The measured peak saturated output power (Po,sat) is 14.8 dBm at 30 GHz. The PA is tested with 64-quadrature-amplitude-modulated signal at a data rate of 1.5 Gb/s. Under this test setup, the PA achieves modulated PAE of 26%/24%/21.4% and average output power (Po,avg) of 9.2/8.8/8.6 dBm at 28, 32, and 34 GHz, respectively, while maintaining better than -25 dB of error vector magnitude and -27 dBc of adjacent channel leakage ratio. To the authors' knowledge, this design presents one of the highest reported PAEs among mmW CMOS PAs.
19 November 2020 in IEEE Journal of Solid-State Circuits
Fully integrated voltage regulators (FIVRs) can improve the performance and reduce the power consumption of a system-on-chip (SoC) by providing point-of-load voltage regulation with dynamic voltage scaling. The desirable attributes of FIVRs include high power efficiency, high power density, and fast transient response, which are difficult to achieve due to on-chip area constraint and parasitic effects. Low-quality and low-density on-chip inductors and capacitors are currently the main performance-limiting factors. This article presents a switched-inductor-capacitor (SIC) voltage converter that can operate more efficiently with compact on-chip air-cored metal-tracked inductors than existing step-down voltage converters. The SIC converter consists of an inductor, a flying capacitor, and three power switches, and it can provide fine-grained voltage regulation by using pulsewidth-modulation (PWM) control. The unique SIC converter topology eases the on-chip inductor integration by positioning the inductor at the input power supply and reducing the current stress of the inductor. A proof-of-concept fully integrated SIC voltage regulator is fabricated in a 65-nm CMOS process, with an area of 1.3 mm x 0.5 mm excluding pads. The output voltage can be regulated from 0.6 to 0.9 V given a 1.2-V input power supply. The output voltage ripple is below 56 mV over the entire range of output voltages and load currents. The peak power efficiency is 78% at an output of 0.9 V and 406 mA. The peak power density is 730 mW/mm², and the peak current density is 820 mA/mm².