10 September 2022 in Particulate Science and Technology
NBNevenka Bošković-Vragolović
Nevenka Bošković-Vragolović
The movement of particles in the fluidized bed primarily determines the mixing in the bed and determines the transfer intensities that occur between the particles and the fluid. Experimental monitoring of the velocity of the marked particle was performed in an inversely fluidized bed of polypropylene, polyethylene, and polystyrene particles. The velocity of the marked particle was monitored in a two-dimensional column, where water and an aqueous solution of glycerin were used as the fluidization medium. Using the Tracker Video Analysis program (Tracker Video Analysis, Open Source Physics, 2003), the mean velocity of the marked particle was determined, as well as the distance crossed by the marked particle in the x and y directions. The influence of fluidization medium viscosity and particle density on the velocity of the marked particle was investigated. The results of experimental investigations have shown that the particle velocity distribution approximately follows the Maxwell distribution. Comparison of the measured values of the mean velocity in the inversely and conventionally fluidized bed showed a certain deviation. In this paper, a correlation for determining the mean particle velocity in an inversely fluidized bed is proposed.
1 January 2023 in Advanced technologies
One of the ways to intensify the process is the use of rotating elements, which increase the mass transfer coefficients many times over. In this study, the mass transfer coefficient was determined by adsorption and electrochemical methods, using a rotating disk (RD) to study the effect of rotation on the mass transfer intensity. For adsorption method, a dilute solution of methylene blue was used, and silica gel foils on rotation disk were used as adsorbents. The measurements were performed under diffusion-controlled conditions, and the color intensity of the surface was determined using SIGMA Scan Pro. The study of mass transfer by electrochemical method was performed in batch systems with a volume of 20 dm3 and 0.8 dm3 , using a solution of sulfuric acid and copper sulfate, and potassium ferricyanide (III), potassium ferricyanide (II), and potassium chloride. Disks with diameters of 0.8 cm, 1 cm, 2 cm, 5.6 cm, and 20 cm were used in the rotation range up to 800 rpm. After determining the operating voltage, the current intensity was measured at different rpm and the mass transfer coefficients were calculated. It was found that the mass transfer coefficient increases as the rotation speed of the RD increases, and that is does not depend on the diameter of RD. It is shown that the current density increases with the increase of the RD speed, while the diffusion layer thickness decreases. A comparative analysis of the results obtained by the adsorption and electrochemical methods was made and the results were compared with literature correlations.
25 February 2023 in Particulate Science and Technology
NVNevenka Bošković Vragolović
Nevenka Bošković Vragolović
To define the fluid-dynamic properties of inverse fluidized beds, studies of the minimum fluidization velocity and bed expansion were performed in this work. The experiments were performed in an inverse fluidized bed of polypropylene and polystyrene particles in a cylindrical column using water and an aqueous glycerol solution of different concentrations as fluidizing medium. The dependence of the bed porosity on the superficial velocity of the fluid was determined experimentally for all the particles studied and different fluidizing media. The influence of fluidizing medium viscosity and particle density on the expansion of the inverse fluidized bed and on the minimum fluidization velocity was investigated. Comparison of the experimental data for the expansion of the inverse fluidized bed and the values calculated by the Richardson-Zaki correlation for the conventional fluidized bed showed some deviation, but the experimentally determined data were found to follow the shape of the Richardson-Zaki curve. In this paper, a correlation for the expansion of inverse fluidized beds is proposed.
10 April 2026 in Chemical Engineering Communications
NVNevenka Bošković Vragolović
Nevenka Bošković Vragolović
+1
Spouted beds have been developed as an efficient approach to contact gas and solid coarse particles (Geldart D) that are difficult to fluidize (Mathur and Gishler 1955). Some drawbacks of the spout...
1 January 2023 in Journal of the Serbian Chemical Society
In this work, the coefficient of fluid-wall mass transfer in an inverse fluidized bed was determined using the adsorption method. The experiments were carried out in a column with a diameter of 45 mm with spherical and non-spherical particles of polypropylene and polyethylene with a diameter of 3.3?4.9 mm and a density of about 930 kg m-3. A diluted solution of methylene blue was used as a fluidization medium, which was adsorbed on part of the surface of the column on silica gel. The obtained results showed that the presence of particles during inverse fluidization does not contribute significantly to mass transfer compared to the influence of particles on transfer in conventional fluidized beds. Therefore, the pseudo-fluid concept was introduced into the analysis and an empirical correlation was performed to determine the mass transfer coefficient. The obtained results were compared with literature correlations for inverse and conventional fluidized beds.
1 January 2024 in Hemijska industrija
Adsorption method has been used for flow visualisation and determination of the local and average mass transfer coefficients around a horizontal cylinder in a liquid-solid fluidized bed. The obtained concentration fields on the adsorbent (silica-foils) represent a clear qualitative flow pattern around the cylinder. By comparison of the concentration fields around the cylinder in the single-phase flow and in the fluidized bed, a significant disturbance of the boundary layer by fluidized particles can be observed. Local mass transfer coefficients were shown to be dependent on the angular position around the cylinder with the maximum determined at the angle 140? (measured from the stagnant point 0?). Selected correlations were applied to predict the average mass transfer coefficients and the two best have shown deviations from the experimental data up to 5 %.