1 October 2023 in Journal of Micro/Nanopatterning, Materials, and Metrology
BackgroundTo print ever smaller features at high contrast projection lithography technology has evolved to shorter wavelength light and larger numerical aperture (NA). After enabling the extreme-ultraviolet (EUV) wavelength, the industry is looking into increasing the NA. At NA’s much higher than 0.55, new effects such as polarization will start to play a role, and larger impact of ultimate mask resolution and material interactions is expected. Already at NA 0.55, a small contrast loss is predicted due to the use of unpolarized light in the scanner. Further increasing the NA beyond 0.55 will exacerbate the contrast loss. In addition, the larger incidence angles on mask when the NA increases above 0.55, will further enhance the mask 3D (M3D) effects forcing additional mask changes.AimStudy the potential imaging challenges regarding NA scaling beyond 0.55 and identify if the imaging can still work at this higher NA and whether specific changes to the mask stack are required.ApproachWe study the polarization effects in detail and assess their impact quantitatively for a set of generic building blocks. To enable proper imaging at high incidence angles, new mask architectures that include changes in the EUV mask absorber and multilayer will have to be tested using rigorous simulations.ResultsThe current periodic Mo/Si multilayer concept is adequate to support 0.75 NA performance. For NA 0.85 aperiodic multilayers would be beneficial. Novel mask absorber materials currently being developed for the 0.33 and 0.55 NA systems are adequate to support 0.75 NA imaging. M3D phase effects slightly increase with NA but can be compensated by adjusting absorber n / k and thickness. Regions of interest in the absorber space remain low-n and high-k. NA 0.75 promises significant normalized image log slope (NILS) gain over NA 0.55 in the L/S pitch range of 20 to 30 nm even when considering M3D effects, existing multilayer periodicity, and no polarizer. For contact holes (CHs), NILS > 2.4 without polarizer can be achieved in both dark and bright mask tonalities for pitches 19 nm and above, even when considering M3D effects, existing multilayer periodicity, and no polarizer. Even if polarization control could provide significant NILS gain for lines and spaces, EUV polarizer may not be worth it in terms of the balance between contrast and throughput. Further validation should be done using a full stochastic resist model in the future. For CHs, the NILS gain possible by polarization is too small to warrant the lost dose.ConclusionsWe identified clear advantages of high NA imaging but found no significant blocking factors for the imaging of the investigated patterns (single pitch lines/spaces and CHs).
10 August 2025 in ACS Applied Materials & Interfaces
1 April 2024 in Japanese Journal of Applied Physics
We are on the eve of the next big step in lithography technology with the introduction of high numerical aperture EUV. The change from NA 0.33–0.55 in EUV lithography is an increase of 67%, which is the largest jump in the last decades, and puts tight requirements on focus and edge placement. Moreover, the lithography system has changed from fully isomorphic, i.e. same demagnification in all directions, to an anamorphic system, i.e. the demagnification in scan direction has doubled with respect to the slit direction. At imec we are fostering the ecosystem surrounding the lithography tool. In this paper we focus on the imaging and mask innovations supporting the EUV ecosystem, which are categorized into four areas: novel absorber masks, stitching, mask variability, and innovative imaging solutions. The current drivers of IC manufacturers implementing (high NA) EUV lithography (EUVL) are reduction of the EUV exposure dose and decrease in wafer stochastics. We discuss how these four areas have the potential to deliver in EUVL an increase in productivity, an improvement in the process window and a reduction in stochasticity at wafer level.
18 November 2024 in Journal of Micro/Nanopatterning, Materials, and Metrology
BackgroundProjection lithography technology has been developed to allow the use of shorter wavelength light and to increase numerical aperture (NA) from 0.33 to 0.55. After enabling extreme-ultraviolet (EUV) wavelengths, to keep up with the scaling trends, the industry would now again like to increase the NA. As the depth of focus (DoF) is inversely proportional to the square of NA, in hyper NA (>0.55) EUV lithography (EUVL), we anticipate that the total available DoF in the lithography process would be further limited.AimWe aim to improve the imaging performance for a wide range of lines and space pitches by minimizing best focus (BF) variations generated from different pitches on an anamorphic EUV mask.ApproachSub-resolution grating (SRG) is proposed to address the increasingly complex design of sub-resolution assisted feature (SRAF), especially in high-NA or hyper-NA regimes where SRAF insertion becomes challenging. We first identify how the mask 3D (M3D) effect-induced BF variation through pitch behaves according to changes in the pattern orientation and mask tone for hyper NA EUVL. We study how various focus shift mitigation strategies can be combined to align the best foci and enhance the image contrast for hyper NA EUVL.ResultsSimulation results indicate that for increased NA, BF variations due to M3D effects for vertical lines deteriorate more significantly than for horizontal lines. As mitigation strategies, we presented diverse solutions in the mask and illumination space, leading to the achievement of well-aligned BF with enhanced image contrast for a broad pitch range and various feature types. By using a phase-less binary mask that has an EUV refractive index of n≅1 and a high EUV extinction coefficient k, the phase offset-induced BF variation through pitch can be mitigated, which could be a favorable option for hyper NA where overlapping DoF becomes crucial. Illumination source optimization in conjunction with aberration injection can correct pole-to-pole offset. SRG in the mask design addresses BF variation through pitch and improves normalized image log slope (NILS) for various patterns, wafer critical dimension targets, and a wide range of exposure dose processes using the most simple and straightforward method. This technique could be one of the best complementary techniques for a high-reflective attenuated phase shift mask also known as a low-n mask.ConclusionsWe identified that SRG aligns BF for various patterns with different pitches, and this can be applied to all absorber thicknesses. In addition, we identified that SRG even improves NILS at certain absorber thicknesses.