Mykola Anyakin

Mykola Anyakin

Auto-generated profile, based on publicly available information

Mykola Anyakin

Igor Sikorsky Kyiv Polytechnic Institute

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in Procedia CIRP
Verified
Journal Article
Open access
VKV. Kovalenko
V. Kovalenko
JYJ. Yao
J. Yao
QZQ. Zhang
Q. Zhang
MNM. Nayebi
M. Nayebi
MAM. Anyakin
M. Anyakin
PKP. Kondrashev
P. Kondrashev
In comparison with high-speed cutting and electrical discharge machining, laser milling is the most universal method for shaping of any type of materials (including natural and artificial diamonds, alloys etc.).The investigation of laser milling was done using Q-switched YAG laser. It was found that the highest productivity and quality of the processing of super-hard materials (when the material is removed layer-by-layer) could be achieved when laser milling is done without the formation of liquid phase or when its quality is minimal (artificial diamonds, borazon).The main reason for the low quality of milling of super-hard materials is uncontrollable surface roughness that is formed when liquid phase is expelled from the hole that is formed under the influence of laser beam. The height of micro-roughness of the processed surface is equal to the thickness of the removed layer. That is why at laser milling of super-hard materials, stainless steels and other similar materials it is recommended to use special techniques that are based on the constant shift of the focusing spot (from layer to layer) according to a specific algorithm

1 January 2007 in CIRP Annals
Verified
Journal Article
Closed access
VKV. Kovalenko
V. Kovalenko
LGL. Golovko
L. Golovko
JMJ. Meijer
J. Meijer
MAM. Anyakin
M. Anyakin

1 January 2013 in Procedia CIRP
Verified
Journal Article
Open access
VKV. Kovalenko
V. Kovalenko
JYJ. Yao
J. Yao
QZQ. Zhang
Q. Zhang
PKP. Kondrashev
P. Kondrashev
MAM. Anyakin
M. Anyakin
OSO. Stepura
O. Stepura
Laser processing technologies like alloying, cladding and rapid prototyping that are based on blowing of gas-powder mixture in the zone of laser processing are very dependent on the alignment of caustic surface (conventional surface that surrounds laser beam) and gas-powder mixture regarding the workpiece surface. Deep knowledge of its behavior is very important for the technologies that use coaxial introduction of gas-powder mixture into the processing zone.By means of numerical modeling with further experimental verification it was found that the shape of the gas-powder stream and its cross-section could be varied with help of the nozzles of various inner shapes. Further investigation of laser cladding technology by means of experiment planning techniques showed statistically significant influence of the position of caustic surface, and gas-powder mixture and the workpiece on the productivity (the size) and quality (presence of cavities) of the clad

1 January 2010 in International Journal of Nanomanufacturing
Verified
Journal Article
Closed access
VKV. Kovalenko
V. Kovalenko
MAM. Anyakin
M. Anyakin
RZR. Zhuk
R. Zhuk
PKP. Kondrashev
P. Kondrashev
OSO. Stepura
O. Stepura
JMJ. Meijer
J. Meijer
Cardio-vascular diseases are the number one killer in the world. As an alternative to common treatment methods the installation of specific-purpose stents into the damaged blood vessel could be used in order to minimise fatal outcomes. Existing technologies of stent manufacturing provide quite good results but are very expensive at the moment. The given paper deals with the design of stents for cardio-vascular surgery and their manufacturing with help of Q-switched Nd-YAG laser which is considered to be much cheaper and more efficient. The methods of nonlinear programming together with methods of experiments planning were used to find the optimal processing conditions and create adequate numerical models of the process. Several processing schemes based on direct laser cutting and step-by-step laser milling had been considered in the research. Some processing dependencies had been established as well as the possibility to create the special micro-relief on the machined surface with help of laser milling. It was demonstrated that due to the assist gas stream action the micro deformation of the stent's workpiece occurs thus influencing the final machining quality.

1 November 1997
Verified
Conference Paper
Closed access
PDF file
VKVolodymyr S. Kovalenko
Volodymyr S. Kovalenko
ALAnatoly M. Lutay
Anatoly M. Lutay
MAMykola S. Anyakin
Mykola S. Anyakin
ZMZraidi Mounir
Zraidi Mounir
Insufficient crack resistance is the significant drawback of laser cladded coatings. To avoid this drawback the technology of laser gas-powder cladding (LGPC) is proposed which includes the action of CW CO2 laser radiation, electric arc and variable magnetic field on material.

1 January 2002
Verified
Conference Paper
Closed access
PDF file
VKV. Kovalenko
V. Kovalenko
MAM. Anyakin
M. Anyakin
JMJ. Meijer
J. Meijer
ADA. Degtyarev
A. Degtyarev
AKA. Kozyrev
A. Kozyrev
The knowledge of optical behavior of materials at laser beam interaction with material surface i of crucial importance for development of different processes of laser material processing the rapi prototyping gaining recently the top priority. Such data may help in determining the optima working conditions, may predict the behavior of the material at laser irradiation. Few works are known devoted to the consideration of this problem [1,2]. Their authors wer using different techniques to find the proper value of optical parameters of some monolithi materials. In some works there had been given data on such characteristics for powder material [3] as well. Those researches were based on evaluation of reflected and diffused beams from irradiated surface, on analysis of acoustics emission of irradiated surface, on monitoring plasm plume generated at interaction of laser beam with surface. The main drawback of all thos techniques was quite high complexity of the monitoring device and procedures. Another negativ factor was the ability to get the result only before or after laser processing itself but not durin processing when surface temperature is influencing surface optical characteristics to great extend. For everyday use at laboratory or at shop floor level the simpler device and technique are neede to get quick results. To perform more efficiently the laser rapid prototyping processing from powder materials we need to know the optical characteristics of different powder material compressed to layers of varied density in their connection with irradiated surface temperature. This paper just demonstrates such simple approach that permits to evaluate the optical parameter depending on surface temperature not only for monolithic materials but for their powde analogues as well.