29 January 2024 in Computer Physics Communications
1 December 2012 in Electrochimica Acta
1 October 2024 in Review of Scientific Instruments
The SPARC tokamak is a high-field, Bt0 ∼12 T, medium-sized, R0 = 1.85 m, tokamak that is presently under construction in Devens, MA, led by Commonwealth Fusion Systems. It will be used to de-risk the high-field tokamak path to a fusion power plant and demonstrate the commercial viability of fusion energy. SPARC’s first campaign plan is to achieve Qfus > 1 using an ICRF-heated, 15 m from the center of the tokamak, on the other side of a 2.4 m concrete shielding wall. A series of 31 large-scale penetrations have been included in the SPARC Tokamak Hall to facilitate integration of early campaign diagnostics and to provide upgradability.
28 June 2024 in Nuclear Fusion
To achieve its performance goals, SPARC plans to operate in equilibrium configurations with a strong elongation of , which in turn will destabilize the n = 0 vertical instability. However, SPARC also features a relatively thick conducting wall that is designed to withstand disruption forces, leading to lower vertical instability growth rates than usually encountered. In this work, we use the TokSyS framework to survey families of accessible shapes near the SPARC baseline configuration, finding maximum growth rates in the range of s−1. The addition of steel vertical stability plates has only a modest ( ) effect on reducing the vertical growth rate and almost no effect on the plasma controllability when the full vertical stability system is taken into account, providing flexibility in the plate conductivity in the SPARC design. Analysis of the maximum controllable displacement on SPARC is used to inform the power supply voltage and current limit requirements needed to control an initial vertical displacement of 5% of the minor radius. From the expected spectra of plasma disturbances and diagnostic noise, requirements for filter latency and vertical stability coil heating tolerances are also obtained. Small modifications to the outboard limiter location are suggested to allow for an unmitigated vertical disturbance as large as 5% of the minor radius without allowing the plasma to become limited. Further, investigations with the 3D COMSOL code reveal that strategic inclusion of insulating structures within the VSC supports are needed to maintain sufficient magnetic response. The workflows presented here help to establish a model for the integrated predictive design for future devices by coupling engineering decisions with physics needs.
25 September 2023 in Nuclear Fusion
Accurate reconstruction of the plasma equilibrium is imperative for successful operation of the SPARC tokamak. In order to assess the expected reconstruction accuracy throughout the duration of design-point discharges, the EFIT equilibrium reconstruction code was deployed for SPARC. Reconstructions from SPARC baseline scenarios were compared with free-boundary equilibria generated by FreeGS, Toksys, and the Tokamak Simulation Code. The key geometric areas of interest, where design constraints are imposed, included: the inner and outer midplane gaps, the X-point locations, as well as the strike point locations. Successful reconstructions of various reference discharges, using deviations in these key geometric quantities as metrics, were calculated from synthetic signals considering an optimized equilibrium magnetic sensor set. The optimization process for this sensor set combined a scan of randomized sensor placement with a linear perturbation analysis to determine critical sensor locations, while simultaneously conforming to design constraints on the sensor placement. This optimized set was also successful in performing equilibrium reconstructions with the addition of error to synthetic measurements of magnetic flux and magnetic field, as well as contributions from eddy currents in conducting structures. These methods represent a workflow of optimization and validation that balances the engineering constraints of sensor placement with achieving sufficient reconstruction fidelity for science and operations missions for SPARC.
1 February 2019 in Review of Scientific Instruments
Rotation of the plasma and MHD modes in tokamaks has been shown to stabilize resistive wall and tearing modes as well as improve confinement through suppression of edge turbulence. In this work, we control mode rotation with a biased electrode inserted into the plasma of the High Beta Tokamak-Extended Pulse’s facility in conjunction with its active GPU (Graphical Processing Unit) feedback system. We first characterize a negative linear relationship between the electrode voltage and mode rotation. Using this relationship, we design, simulate, and implement a proof-of-concept, GPU-based active-control system, which shows consistent success in controlling mode rotation in both feedforward and feedback operation. Controllability is limited by operating conditions, the electrode’s voltage range, and by the electrode’s proximity to the vessel’s walls. The final control system has a 15 μs cycle time, but the addition of various signal filters results in a full cycle latency of 200 μs.