Muhamad Saifuddin Salim

Muhamad Saifuddin Salim

Auto-generated profile, based on publicly available information

Muhamad Saifuddin Salim

Universiti Sains Malaysia

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2017 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
LJLee Joyyi
Lee Joyyi
MTMohd Zharif Ahmad Thirmizir
Mohd Zharif Ahmad Thirmizir
MSMuhamad Saifuddin Salim
Muhamad Saifuddin Salim
LHLizhu Han
Lizhu Han
PMParamasivam Murugan
Paramasivam Murugan
KSKumar Sudesh
Kumar Sudesh

30 May 2015 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
DADody Ariawan
Dody Ariawan
ZIZ.A. Mohd Ishak
Z.A. Mohd Ishak
MSM.S. Salim
M.S. Salim
RTR. Mat Taib
R. Mat Taib
MTM.Z. Ahmad Thirmizir
M.Z. Ahmad Thirmizir

13 June 2017 in Composite Interfaces
Verified
Journal Article
Closed access
DADody Ariawan
Dody Ariawan
MSM. S. Salim
M. S. Salim
RTR. Mat Taib
R. Mat Taib
MTM. Z. Ahmad Thirmizir
M. Z. Ahmad Thirmizir
ZIZ. A. Mohd Ishak
Z. A. Mohd Ishak
This paper reports on the comprehensive characterisation of heat treated kenaf fibre (KF) and its composites. The kenaf fibres were modified by heating for 2.5–12.5 h inside a drying oven. Heat treatment produces an increase in the crystallinity index and fibre strength of KF. The highest value of KF strength was recorded by applying heat treatment of 10 h on KF. The heat treatment results in the partial removal of impurities/extractives on the KF surface which is detected by scanning electron microscopy and X-ray photoelectron spectroscopy. Atomic force microscopy results signify the decrease of roughness, the increase in peak area density and the increase of the adhesion force on the surface area of heat treated KF. The effect of the heat treatment in enhancing the interface bonding characteristics between the KF and unsaturated polyester matrix can be reflected by the interlaminar shear strength (ILSS) and dynamic mechanical analysis value of the composites. The flexural properties of the composites showed a similar trend to ILSS. However, the fracture toughness revealed contrasting results. Water absorption induced a drastic loss of the mechanical properties of the composites albeit better retention of properties was observed in the case of heat-treated KF composites.

5 October 2017 in Polymer Composites
Verified
Journal Article
Closed access
PDF file
MSM.S. Salim
M.S. Salim
DADody Ariawan
Dody Ariawan
MRM.F. Ahmad Rasyid
M.F. Ahmad Rasyid
MTM.Z. Ahmad Thirmizir
M.Z. Ahmad Thirmizir
RTR. Mat Taib
R. Mat Taib
ZIZ.A. Mohd. Ishak
Z.A. Mohd. Ishak

1 January 2016 in Procedia Chemistry
Verified
Journal Article
Open access
MRM.F. Ahmad Rasyid
M.F. Ahmad Rasyid
MSM.S. Salim
M.S. Salim
HAHazizan Md Akil
Hazizan Md Akil
ZIZ.A.M. Ishak
Z.A.M. Ishak
Currently, there is a significant drive to switch to more sustainable and renewable materials, whilst still reducing weight and cost and maintaining reliability. In addition, with some renewable materials, end-of-life vehicle issues are more easily addressed because the materials are biodegradable or easily recycled. Natural fibres such as flax fibre (FF)have several advantages that have made them particularly attractive to the automobile industry. These include relatively good mechanical strength, low density better thermal and acoustic insulation and low cost. The aim of this study was to produce optimised Nonwoven Flax Fibre Reinforced Acrodur (NWFA) biocomposites. Response surface methodology (RSM) was employed to study the effect of processing conditions such as moisture content, curing temperature and curing time on flexural strength and modulus. The optimized conditions was analyzed using Analysis of Variance (ANOVA) and the optimized value for the maximum flexural strength of NWFA biocomposites was found at 25% moisture content, 1700C curing temperature and 180seconds curing time. Maximum flexural strength and modulus of 44.83MPa and 4.70GPa were attained. From the analysis of variance (ANOVA) technique, namely the Box–Behnken method, curing temperature significantly affects the strength of NWFA biocomposites, followed by the moisture content and curing time. The P-value of the model of the experiment is less than 0.05 and the determination coefficient (R2) is nearly 1 suggesting that the model is significant and implies on the precision and processability in the production

1 January 2019 in Express Polymer Letters
Verified
Journal Article
Closed access
MRM. F. Ahmad Rasyid
M. F. Ahmad Rasyid
MSM. S. Salim
M. S. Salim
HAH. M. Akil
H. M. Akil
JKJ. Karger-Kocsis
J. Karger-Kocsis
ZIZ. A. Mohd. Ishak
Z. A. Mohd. Ishak