Laboratory of Porous Media and Fluid Dynamics, Physics of Earth and Complex Systems, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Bandung, Indonesia
Auto-generated profile, based on publicly available information
Umar Fauzi
Laboratory of Porous Media and Fluid Dynamics, Physics of Earth and Complex Systems, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Bandung, Indonesia
Calculation of permeability from 3D tomographic rock images was performed by combining renormalization group approaches (RGA) and lattice Boltzmann method (LBM). Images of sandstone rock samples (i.e., Fontainebleau, Berea, and Sumatera sandstones) with block size of 2563 voxels were used in this study. LBM was applied to calculate permeability of each smallest block (i.e., 64 and 128 voxels) as sub-blocks of the larger block (2563 voxels). The calculated permeability will form analogue to hydraulic conductance networks. RGA were then applied to the networks for all three perpendicular directions using several RGA schemes, i.e., King, Karim–Krabbenhoft, Green–Paterson, and their combinations. It was shown that as the number of renormalizations increases, the average permeability decreases. The effective permeability calculated by combining RGA and LBM were lower than permeability of the single largest block. Karim and Krabbenhoft’s scheme produced mostly higher estimation than the others and closest to the true permeability. Degree of anisotropy is influenced by the initial block size prior to RGA scheme.
16 January 2023 in International Journal of Geophysics
The assumption of a homogeneous elastic half-space model is widely used to model the earth’s deformation. However, the homogeneous assumption would not accurately reflect the complexity of the shallow crust. We performed a 3D coseismic deformation model using the finite element method and referred to the 2010 Mentawai earthquake. The 2010 tsunami earthquake was located at the Mentawai segment, which is a part of the accretionary wedge in the Sumatra subduction zone. This active accretionary wedge is identified as the most complicated structure on earth and lies along the Sumatra subduction zone, at which most destructive earthquakes happen in this region. We examined the impact of the accretionary wedge geometry and material properties by considering the wedge as a single different property separated from the continental plate. Various geometrical features, such as topography and wedge dimension, as well as physical properties, were simulated. Those features are then observed for their responses on the surface deformation. The topography affected the magnitude of the horizontal deformation up to 10% but only the pattern of the vertical deformation. The wedge dimension seems to have an insignificant influence on the surface deformation compared to the topography. Different physical properties of the accretionary wedge affect not only the magnitude of the horizontal deformation up to 40% but also the orientation. The direction of the lateral movement is seemingly affected by the material under the GPS station and by the source. On the other hand, the variations in the physical properties resulted in discrepancies of 0.5 meters in the vertical deformation near the source. These results indicated that regional physical property information and geometrical features are critical in estimating coseismic deformation, leading to more accurate slip inversion and earthquake and tsunami hazard prediction, particularly in regions with significant inhomogeneity.
28 May 2024 in Modeling Earth Systems and Environment
Interaction between fluids and solid surfaces plays important roles in many fields, e.g.: enhanced oil recovery (EOR), environmental engineering, agriculture, materials, etc. Research on this topic is intensively carried out by many researchers. In this research, a simple experimental setup for fluid contact angle measurement is constructed using an optical microscope and video camera with 29 frames per second. Measurement of contact angle of fluid with variation of salinity, i.e.: 1M, 2M, 3M, 4M, and 5M is carried out by recording a single droplet placed on a rock surface. Each frame of the recorded video are then analysed using image processing technique to detect the edge and calculate the contact angle. A single 8th order polynomial was applied to the edge of the wetting type droplet, but two types of polynomial fitting curves are applied for edge of non-wetting type droplet. It is obtained that on preparatory glass, the higher the molarity, the longer the droplet will evaporated. On the sandstone surface, fluid contact angle on sandstone surface is about 80° and decreases with time with different trend of decrement. This may be due to complex interaction between fluid and pores at sandstone surface spot.
Tortuosity, percolation probability and porosity are important rock parameters because all those things affect the fluid flow in rocks. In this study, 3-dimensional cube-shaped rock models were randomly generated with N × N × N size containing matrices and pores. Rock models were made with porosities ranging from 0.1 to 1 with increasing of value 0.1. The selected N is N = 5, 6, 7, 8, 9, 10, 25, 125 and for every N there are 10,000 random configurations. Then, tortuosity was calculated using a nearest-neighbor sites method with 6 neighboring sides. In addition, with the site percolation model, percolation probability was calculated by determining the comparison between the number of percolate configurations and the total number of configurations created. The results show that in large-size rock models, the average tortuosity will increase. Further, the percolation probability is zero at a small porosity and rises to 1 as the porosity increases. Moreover, the slope of the percolation probability curve will increase for the larger model. In other words, the larger the size of the model, the percolation threshold will become larger or more difficult to percolate for small porosity.