17 March 2021 in Advanced Optical Materials
A platform is introduced for fabrication of a reusable and highly efficient low band gap photocatalyst by confining gold nanoparticles (AuNPs) in the pores of a nanopatterned Si monolith (AuNSM). Due to their size, a maximum of two AuNPs can assemble in a single pore, thus preventing agglomerations. Their access to the analyte provides more active sites for redox reaction, leading to enhanced efficiency. While proximity of nanoparticles enhances coupling efficiency, confinement prevents rapid recombination of photogenerated charge carriers, a major factor contributing to low efficiency of photocatalytic materials. Degradation of methyl orange (MO) is used to determine the photocatalytic efficacy of AuNSM compared to 1) bare silicon and 2) AuNPs randomly dispersed on silicon. After 90 min of exposure to UV light (λ = 353 nm) in the AuNSM, the MO absorption is <1%, indicating near complete degradation, while it is still 85% and 70% for systems (1) and (2), respectively. Finite element method simulations of the confined structure suggest that the AuNPs act as a mediator/receptacle for photogenerated charges rather than a source of them at this wavelength and thus enhance the performance of the photocatalyst by creating more effective Schottky junctions—preventing recombination of electrons and holes—rather than by a localized surface plasmonic resonance effect.
9 July 2018 in Optics Express
To achieve a feasible heat-assisted magnetic recording (HAMR) system, a near-field transducer (NFT) is necessary to strongly focus the optical field to a lateral region measuring tens of nanometres in size. An NFT must deliver sufficient power to the recording medium as well as maintain its structural integrity. The self-heating problem in the NFT causes materials failure that leads to the degradation of the hard disk drive performance. The literature reports NFT structures with physical sizes well below 1 micron which were found to be thermo-mechanically unstable at an elevated temperature. In this paper, we demonstrate an adiabatic NFT to address the central challenge of thermal engineering for a HAMR system. The NFT is formed by an isosceles triangular gold taper plasmonic waveguide with a length of 6 µm and a height of 50 nm. Our study shows that in the full optically and thermally optimized system, the NFT efficiently extracts the incident light from the waveguide core and can improve the shape of the heating source profile for data recording. The most important insight of the thermal performance is that the recording medium can be heated up to 866 K with an input power of 8.5 mW which is above the Curie temperature of the FePt film while maintaining the temperature in the NFT at 390 K without a heat spreader. A very good thermal efficiency of 5.91 is achieved also. The proposed structure is easily fabricated and can potentially reduce the NFT deformation at a high recording temperature making it suitable for practical HAMR application.
6 December 2016 in Journal of Optics
A simple experimental method for determining the number of modes in planar dielectric multi-mode waveguides, and the effective index difference of these modes, is presented. Applying a thin, dye-doped polymer cladding, the fluorescence excited by multiple modes propagating in a silicon nitride slab waveguide is imaged to extract information. Interference between the modes produces a structured intensity profile along the waveguide which is constant in time. The spatial frequencies of this intensity profile are directly linked to the propagation constants of the underlying modes. Through a discrete Fourier transform, the modes' effective index differences are found and compare well with analytically calculated values. Furthermore, the amplitudes in the Fourier transform are directly related to the power in each mode. Comparing the amplitudes of the Fourier components as a function of propagation distance, an estimate of the propagation losses of the individual modes relative to one another is made. The method discussed could be applied to analysing mode behaviour in integrated photonic devices, most notably in mode-division multiplexing.
14 July 2022 in Journal of Micromechanics and Microengineering
A method for producing large-area, broadband, quasi-omnidirectional low-reflectivity glass surfaces is presented. Using block copolymer patterning and inductively coupled plasma etching, near-periodic arrays of pillars are formed in glass. The patterned surface has reflectivity 0.5%—almost an order of magnitude smaller than plain glass—with a bandwidth of ∼300 nm. Substrates etched on both sides transmit 99.5% across the wavelength range 850–1200 nm, with 99% down to λ = 650 nm. The process is demonstrated on a 5 cm diameter fused silica wafer and high transmittance is maintained up to at least 70∘ incidence. The resulting substrates might find application as lab optics (windows, lenses, etc) display screens for televisions, computers, phones, and as encapsulants for optoelectronic devices.
16 July 2018 in Optics Letters
A design process for creating integrated diffractive focusing elements for use in planar waveguides is presented. The elements consist of a linear array of holes etched into the core layer of a planar dielectric waveguide. A complete element is a few micrometers in size, while the individual holes are sub-micrometer. The focusing element was designed using analytical Mie theory. The performance of the complete 3D structure was then evaluated using 3D finite difference time domain (FDTD) method. A focal spot width of 227 nm (full width at half maximum) was predicted by 3D FDTD simulations with a peak intensity more than 10x the incident intensity and back-reflections lower than 1%. The focusing elements were fabricated using electron beam lithography and plasma etching. Fluorescence imaging was used to map the intensity in the waveguide core. The experimentally measured intensity maps were in good agreement with the simulations when the finite spatial resolution of the imaging system was taken into account.