28 October 2025 in Technobius
This study investigates diatomite-based silica ceramics designed for low thermal conductivity, using diatomite from the Utesai deposit (Aktobe region, Kazakhstan) and loam from the Romanovskoye deposit (West Kazakhstan region, Kazakhstan) as a modifying additive. The raw diatomite is characterized by high porosity and low thermal conductivity, while the ground fraction shows favorable technological behavior for ceramic processing, including low drying sensitivity. Calcination at 950 °C increases density and thermal conductivity, indicating partial densification. Silica-ceramic specimens were produced by plastic and semi-dry molding and fired at 950 °C, both from pure diatomite and from a diatomite-loam composition. The results show that 10% loam addition improves the fired structure: density and strength increase, whereas water absorption and total shrinkage decrease, with only minor changes in thermal conductivity. The combined trends demonstrate the feasibility of producing lightweight silica ceramics with improved integrity while maintaining heat-insulating performance.
31 March 2026 in Батыс Қазақстан инновациялық-технологиялық университетінің Хабаршысы
The article reflects the material of the economic agreement dated March 17, 2025, between the Private Educational Institution of Higher Education «Western Kazakhstan Innovation and Technology University» and СF «AiMak», registered under No. 0226RK0017 in JC «National Center for State Scientific and Technical Expertise», on the topic: Conducting a literature and patent search and studying the properties of raw material components. The main methods and techniques for studying and researching the technology of binding materials based on mineral raw materials – opoka. The objective of the scientific research is to analyze the possibility of using natural mineral raw materials to develop binding material technology in the production of building materials. The goal of the research work is to develop a technology for the production of cement based on opoka from the Shipovsky deposit in the Western region of Kazakhstan for modern civil and industrial construction in the Republic of Kazakhstan. The article highlights the nature of the origin of opoka. The physical and mechanical properties of the opoka were studied through laboratory research using the instruments and equipment of the university's building materials laboratory. As a result of the scientific research, the main physical and mechanical properties of the opoka were determined.
30 September 2026 in Батыс Қазақстан инновациялық-технологиялық университетінің Хабаршысы
The article reflects the results of studies of the siliceous rock of the Western Kazakhstan region. The developed technology for the production of flask-based building materials for use in civil, industrial and road construction is presented. The physicomechanical properties of the flask, as well as building materials such as lightweight concretes based on them, have been determined. The article describes the main methods and methods for studying and researching natural fossils related to siliceous rocks. The objective of the scientific study of the flask is to analyze the possibility of application in the production of concrete products and structures. The flask was studied as an independent material and as a raw material for the manufacture of thermolith used as a filler for the production of building materials such as thermite, thermal furnace, aerated concrete and thermolith concrete. The purpose of the research is to develop technology for the production of concrete products and structures. The physico-mechanical properties of laboratory concrete samples were studied by laboratory studies using instruments and equipment from the university laboratory. As a result of the conducted scientific research, the main physico-mechanical properties of thermite, heat shield, aerated concrete and thermolith concrete were determined. A technological line has been designed, consisting of a single-roll plate crusher for crushing large pieces of raw materials larger than 300 mm in size and a double-roll tooth crusher for crushing pieces smaller than 300 mm in size, installed in the technological line sequentially, crushing pieces of flask with sizes up to 600 – 650 mm with a yield of plate grains and needle-shaped, not more than 10% by weight.
27 September 2024 in Батыс Қазақстан инновациялық-технологиялық университетінің Хабаршысы
The article presents the results of a study of the chemical and mineralogical composition of the raw material components in the ceramic mass and provides techniques for the technology of laying ceramic material by vibropressing using talc rock in the mass and methods for determining the composition of clay raw materials. Formulations for the production of ceramic road surfaces, taking into account the factors of preference for mixtures to improve the properties of the finished product as a molding, drying and ceramic material, have been studied in two different components. It was found that the introduction of talc into the ceramic composition has an effect on the formation of high-temperature augite and amphibole phases and the intensification of the formation of minerals in clay, on the formation of high-temperature phases - sanidine, ackermanite elements. This process leads to an increase in the physical and mechanical properties of the resulting samples.The main patterns of formation of the structure and phase of ceramic compositions by firing in the temperature range 1000оC-1100оC were studied by isothermal control.In this pattern, sintering processes with solid and solid liquid-phase syntheses were carried out to ensure the phase - mineral composition, the study clarified the production of high-strength and frost-resistant ceramic pavement. In order to be used in the improvement of the city territory (sidewalks, alleys, park areas, playgrounds, etc.), the possibility of obtaining ceramic road surfaces that meet environmental and operational requirements has been proven. It has been established that one of the priority properties of ceramic road surfaces is a significant abundance of their porosity (25-30%), which allows you to quickly absorb moisture from precipitation (rain, sleet, etc.) and filter water through the body into the ground.Such properties of ceramic paving stones prevent the accumulation of moisture on the surface of the roadway and create comfortable conditions during pedestrian movement, reducing the likelihood of ice formation on the surface of the paving stones in the cold season.
30 June 2025 in Батыс Қазақстан инновациялық-технологиялық университетінің Хабаршысы
The article reflects the main methods and methods of studying and using in the industry of building materials of a natural fossil belonging to siliceous rocks - opoki.The nature of the origin of the flock, its deposits, and analysis of reserves are covered.As a result of the study of the Shipovskoye opoki field in the West Kazakhstan region of the Republic of Kazakhstan, several dozen samples were taken at various depths and at various points along the perimeter of the field.The properties of opoka were studied through laboratory studies, methods of mineral-petrographic, physical, chemical and other types of analyzes were used. Opoka was studied as an independent material for the production of building materials and as a raw material for the manufacture of thermolith, used as a light (large and small) aggregate in the manufacture of concrete products and structures and asphalt concrete.Thermolite was obtained in laboratory and industrial conditions by high-temperature burning of flock at 1150 ° C.laboratory studies of thermolite in accredited testing laboratories have shown compliance of its chemical composition, strength properties and radiation safety with regulatory requirements.Based on the thermolite tests performed, a product quality certificate was obtained. A technology for the production of products from peat was developed, a lightweight full-bodied brick was obtained.On the basis of thermolite, used as a large aggregate, a building material is obtained - light concrete for the manufacture of light concrete blocks, paving slabs and paving curbs.Asphalt concrete is made for the construction of a road surface based on thermolith.Selected technological equipment for the manufacture of building materials and products. Keywords: flask, construction materials, siliceous opal-cristobalite rock, thermolite, aggregate, lightweight brick, certificate.
30 September 2025 in Батыс Қазақстан инновациялық-технологиялық университетінің Хабаршысы
The article reflects the main methods and methods for the study, research and application in the industry of building materials of a natural fossil, diamithite, related to siliceous rocks. The objective of scientific research of diatomite in Aktobe region is to analyze the possibility of using diatomite by construction organizations in modern civil and industrial construction, and to develop technology for the production of diatomite thermal insulation bricks. The purpose of the research work is to develop a technology for the production of energy-saving building materials based on diatomite from the Western region of Kazakhstan for modern civil and industrial construction in the Republic of Kazakhstan. The article highlights the nature of the origin of diatomite. The physico-mechanical properties of diatomite were studied by laboratory studies using instruments and equipment from the University's laboratory for building materials. Diatomite was studied as an independent material and as a raw material for the manufacture of thermolith used as a filler for the production of building materials. The thermolith was made in the laboratory by high-temperature roasting of the flask at a temperature of 1150°C. As a result of the conducted scientific research, the main physical and mechanical properties of diatomite, thermolith and diatomite thermal insulation bricks were determined.