Youngbin Yoon

Youngbin Yoon

Auto-generated profile, based on publicly available information

Youngbin Yoon

Department of Aerospace Engineering, Seoul National University

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2014 in Combustion and Flame
Verified
Journal Article
Closed access
NBNicolas Bouvet
Nicolas Bouvet
DDDmitry Davidenko
Dmitry Davidenko
CCChristian Chauveau
Christian Chauveau
LPLaure Pillier
Laure Pillier
YYYoungbin Yoon
Youngbin Yoon

18 December 2023 in Acta Astronautica
Verified
Journal Article
Closed access
SHSubeom Heo
Subeom Heo
JJJuhwan Jeong
Juhwan Jeong
YYYoungbin Yoon
Youngbin Yoon

4 November 2013 in Combustion Science and Technology
Verified
Journal Article
Closed access
JHJeongjae Hwang
Jeongjae Hwang
KSKitae Sohn
Kitae Sohn
NBNicolas Bouvet
Nicolas Bouvet
YYYoungbin Yoon
Youngbin Yoon
NOx emission characteristics and EINOx scaling of hydrogen and H2/CO syngas non-premixed jet flames under turbulent condition are investigated. Flame length and NOx concentration were measured simultaneously for four different syngas compositions (100/0, 75/25, 50/50, and 25/75 H2/CO% vol.) and three different fuel nozzle diameters (2.5, 3.0, and 3.5 mm). The jet flames were in the buoyancy-momentum transition regime. NOx emission is reduced with increased Reynolds number and increased CO content in the syngas fuel, which result from a decreased flame residence time. The previous EINOx scaling correlation, which is based on flame residence time (flame volume divided by volume flow rate of fuel), does not apply to a hydrogen jet flame in the buoyancy-momentum transition region. The previous scaling applies only to momentum-dominated jet flames. A modified scaling based on a simplified flame residence time (flame length divided by fuel jet velocity) considered the buoyancy effect as proposed. This scaling aligns the 1/2-power with the jet flame in both momentum-dominated and transition regions. The modified scaling also satisfies the 1/2 slope with H2/CO syngas jet flames. Furthermore, the proposed modified scaling adopts the nitrogen amount as a reference, instead of the fuel amount. Finally, the modified scaling collapses the all syngas compositions into a single line.

15 March 2015 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
JYJisu Yoon
Jisu Yoon
MLMin-Chul Lee
Min-Chul Lee
SJSeongpil Joo
Seongpil Joo
JKJeongjin Kim
Jeongjin Kim
YYYoungbin Yoon
Youngbin Yoon

1 June 2006 in Journal of Visualization
Verified
Journal Article
Closed access
PDF file
HKH. Koh
H. Koh
KJK. Jung
K. Jung
YYY. Yoon
Y. Yoon
KLK. Lee
K. Lee
KJK. S. Jeong
K. S. Jeong

21 March 2024 in International Journal of Aeronautical and Space Sciences
Verified
Journal Article
Open access
PDF file
ILIngyu Lee
Ingyu Lee
DSDaewoong Shim
Daewoong Shim
IKInho Kim
Inho Kim
YYYoungbin Yoon
Youngbin Yoon
Due to the structural characteristics of the pintle injector, a recirculation zone is generated under the pintle, so the pintle tip is directly exposed to a high-temperature environment. Therefore, the cooling technique and protective coating on the pintle tip are essential for improving the reusability and durability of the pintle injector. Although various cooling methods are known, this study applied a forced flow passage cooling method by adding internal structures called inserts to the pintle injector. The characteristics of the insert were analyzed experimentally and numerically based on change of its area ratio. When the internal flow changes, the spray angle, droplet size, and cooling performance also change in accordance with an increase in the insert’s central area. When the insert structure is installed in the pintle post, upward flow may occur, which can worsen the spray angle and droplet distribution characteristics. Nevertheless, owing to the insert structure, the surface temperature of the pintle post is reduced dramatically as intended. Thus, an optimal design technique for cooling by changing the area ratio of the first- and second-row slits of the pintle post can be suggested to overcome the limitations of the insert structure. The results of this study will be helpful in understanding the spray characteristics of the insert structure and optimize the design of cooling channels for reusable pintle injectors in the future.