16 December 2013 in IOP Conference Series: Materials Science and Engineering
This paper presents the numerical investigation via Computational Fluid Dynamic (CFD) to study the effect of plenum chamber depth on air flow a distribution in a swirling fluidized bed (SFB). A total of 9 simulations were conducted for 3 plenum chamber depths of 175 mm, 350 mm and 525 mm (below the distributor) for 3 different inlets: single, double and triple inlets. Air flow distribution was analyzed based on the tangential velocity distribution ad pressure drop at the distributor outlet. Statistical parameters used in characterizing the air flow distribution were standard deviation, skewness and kurtosis together with system pressure drop. An optimum plenum chamber depth has low statistical values, implying a uniform velocity distribution inside the bed while low pressure drops are necessary to reduce energy loss in the system. The findings yield that plenum chamber with 175 mm depth with via triple inlets suffices both criteria of high uniformity and low pressure drops.
17 July 2014 in MATEC Web of Conferences
27 June 2021 in Journal of Thermal Analysis and Calorimetry
1 October 2014 in Applied Mechanics and Materials
MZMohd Zarhamdy Mohd Zain
Utilization of alternative fuels and utilization of waste heat has also become a major research area. This study reports on an investigation on a development of an energy converter of heat engine that converts energy from a waste heat flow process into acoustic power. The energy power converter operates with a temperature gradient imposed on a Celcor ceramic stack which then induces pressure oscillations. The system consists of a simple stainless steel pipe tube with a range of diameter open at one end. A waste heat gas is used to model a potential heat source from automobile engine. A two heat exchanger is required while copper plates are used as the ambient heat exchanger and hot heat exchanger. Effects on pressure oscillations have been observed with a calculated heat rate of 50 W at the stack. The system which operates at atmospheric pressure with air as the working fluid indicates a potential in utilizing the heat produced from waste heat automobile engine into making a new energy resource.
21 December 2020 in CFD Letters
RKRiyadhthusollehan Khairulfuaad
Riyadhthusollehan Khairulfuaad
Coronavirus disease 2019 (COVID-19) caused by severe acute respiratory coronavirus-2 syndrome (SARS-CoV-2) were first reported by officials in Wuhan City, China, in December 2019. COVID-19 patients have a symptom of respiratory pneumonia diseases which have difficulties in breathing normally. Previously, the nebulizer machine commonly used to treat respiratory pneumonia diseases. However, the usage for this machine was not suggested during this COVID-19 period because the virus will be spread off easily. To overcome these shortcomings, the uses of Metered-Dose Inhaler (MDI) with MDI disposable inhaler spacer is preferable. Besides, it had been known that the used of MDI disposable inhaler spacer helps to increase the uptaking of the drug into the lung. Besides that, the high demand for the MDI Disposable Inhaler Spacer in the hospital, causing a shortage of supply in Malaysia. Thus, this study aims to produce a new design of this spacer to full fill the market need. This new design of MDI Disposable Inhaler Spacer (AeroCup) was designed by using Solid Work 2018. Then, the parameters for flow characteristic such as particle velocity magnitude, velocity, Eddy viscosity, turbulence Eddy dissipation and turbulence kinetic energy (TKE) was successfully characterized and compared with commercial design A using ANSYS Fluent Version 19.2. The result showed that new design (AeroCup) had the desired characteristic, which was almost similar to commercial design A. This study can provide a piece of information to produce the low-cost metered-dose inhaler (MDI) disposable inhaler spacer to enlighten the burden shouldered by front liners, especially during the pandemic and also can scale-up the economic viability.
5 December 2021 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
This study aims to explore the knowledge on fluid flow properties of the aqueous humour (AH), specifically on the anterior segment (AS) of the human eye for a medical condition called Glaucoma. The research objectives are to study on fluid flow characteristics of velocity and pressure of the AH on the AS of the eye using enlarged 3D printed model and computational analysis, and also to analyse the suitability of the 3D generated anterior AS in fluid flow analysis application on particle image velocimetry (PIV). Using polyvinyl alcohol (PVA) as a water-soluble 3D printing filament, a 3D model of the AS of the human eye was generated with SolidWorks 2018 and printed using Creality Ender 3. This printed model serves as the pattern for silicon rubber mould production using vacuum casting process. Analysis of AH flow hydrodynamics are conducted with computational analysis using ANSYS Workbench 19.2. Key findings support that use of PVA material suite the creation of specific shapes and patterns for 3D modelling applications alike, and silicon rubber moulding creates a non-reactive and long-lasting mould for PIV applications. Computational analysis findings support the use of the generated model for PIV applications. Overall, the study successfully supports the use of 3D printed model for PIV application and future work that can be induced include direct experimentation of the mould with PIV.