S. M. Muzakkir

S. M. Muzakkir

Auto-generated profile, based on publicly available information

S. M. Muzakkir

Department of Mechanical Engineering, Jamia Millia Islamia, New Delhi, India

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 February 2023 in Journal of Sound and Vibration
Verified
Journal Article
Closed access
SMSameera Mufazzal
Sameera Mufazzal
SMSm Muzakkir
Sm Muzakkir
SKSidra Khanam
Sidra Khanam

1 May 2014 in Engineering Failure Analysis
Verified
Journal Article
Closed access
SMS.M. Muzakkir
S.M. Muzakkir
LKLijesh Koottaparambil
Lijesh Koottaparambil
HHHarish Hirani
Harish Hirani

1 December 2011 in Engineering Failure Analysis
Verified
Journal Article
Closed access
SMS.M. Muzakkir
S.M. Muzakkir
HHHarish Hirani
Harish Hirani
GTG.D. Thakre
G.D. Thakre
MTM.R. Tyagi
M.R. Tyagi

18 July 2013 in Tribology Transactions
Verified
Journal Article
Closed access
SMS. M. Muzakkir
S. M. Muzakkir
HHHarish Hirani
Harish Hirani
GTG. D. Thakre
G. D. Thakre
Slow-speed journal bearings subjected to heavy loads operate in a mixed/boundary lubrication regime. Clearance and lubricant play very important roles in reducing the wear and friction in these bearings. In the present article, an experimental study on heavily loaded slow-speed journal bearings with various radial clearances lubricated with three different lubricants is presented. Lubricants with varying viscosities and containing different percentages of antiwear additives have been used. Bearing surface roughness and out-of-roundness are treated as noise parameters. The results of friction coefficient and total wear have been reported. The experimental results suggest that a lubricant with high viscosity and antiwear additives significantly reduces the coefficient of friction and amount of wear under varying bearing clearances, circularity, and cylindricity. The use of such a robust lubricant may obviate the effect of manufacturing uncertainties. This results in reduction of manufacturing and measurement costs.

8 June 2018 in Tribology - Materials, Surfaces & Interfaces
Verified
Journal Article
Closed access
DKDeepak Kumar
Deepak Kumar
KDK. B. Deepak
K. B. Deepak
SMS. M. Muzakkir
S. M. Muzakkir
MWMohammad Farooq Wani
Mohammad Farooq Wani
LKLijesh Koottaparambil
Lijesh Koottaparambil
The exceptional combination of mechanical, physical and anti-corrosive properties of Titanium alloy Ti-6Al-4 V (Ti64) makes it idle material for the applications like aerospace, automobile, chemical, medical etc. However, Ti64 exhibits poor tribological (friction and wear) properties, which limits its implementation in the intended applications. The tribological performance of the Ti64 can be enhanced by developing a protective layer or coating on its surface. It has been reported in literatures that through rubbing process the oxide layers can be achieved at much lower temperature compared to external heating process. Therefore, an endeavour is made in the present work to achieve a tribo-oxide protective layer on the surface of Ti64 through rubbing process. For this, at first the tribological behaviour of tribo pair: Ti64 pin-alumina disc is studied under dry ambient condition for diverse loading and sliding speed conditions, using pin on disc experimental set-up. The obtained results are compared with literatures. The tribological performance is quantified in terms of coefficient of friction (COF) and wear rate. To investigate the tribological mechanism and behaviour, in-situ analysis was performed on the pin’s surface using (i) scanning electron microscopy, and (ii) energy dispersive analysis of X-ray. The mechanical properties like nano-hardness and elastic modulus of the pins surface were also determined. It was envisaged that the tribological behaviour were extremely transient and depend greatly on what the surface has precisely experienced Based on the experimental observations, the experimental conditions providing (i) Case1: deprived tribological properties and (ii) Case 2: higher oxide layer is selected. Now, to enhance the tribological behaviour of Case 1, the pin with high oxide layer, i.e. Case 2 is used. For this experiment is performed initially for Case 2 conditions for the sliding distance of 1000 m (for developing oxide layer) and the experiment is continued for next 1000 m for Case 1 condition. The experimental results in terms of COF and wear rate are presented and corresponding enhancement in their values are discussed.

1 April 2016 in Engineering Failure Analysis
Verified
Journal Article
Closed access
LKLijesh Koottaparambil
Lijesh Koottaparambil
SMS.M. Muzakkir
S.M. Muzakkir
HHHarish Hirani
Harish Hirani