Sayan Biswas

Sayan Biswas

Auto-generated profile, based on publicly available information

Sayan Biswas

Department of Mechanical Engineering, University of Minnesota , Minneapolis, Minnesota 55414

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2016 in Applied Thermal Engineering
Verified
Journal Article
Closed access
SBSayan Biswas
Sayan Biswas
STSaad Tanvir
Saad Tanvir
HWHaifeng Wang
Haifeng Wang
LQLi Qiao
Li Qiao

1 March 2018 in Applied Thermal Engineering
Verified
Journal Article
Closed access
SBSayan Biswas
Sayan Biswas
LQLi Qiao
Li Qiao

5 April 2016 in SAE International Journal of Engines
Verified
Journal Article
Closed access
SBSayan Biswas
Sayan Biswas
LQLi Qiao
Li Qiao
An experiment has been developed to investigate the ignition characteristics of ultra-lean premixed H2/air mixtures by a supersonic hot jet. The hot jet is generated by combustion of a stoichiometric mixture in a small prechamber. The apparatus adopted a dual-chamber design in which a small-volume (1% of the main chamber by volume) prechamber was installed within a large-volume main chamber. A small orifice (nozzle) connects the two chambers. Spark initiated combustion inside the prechamber causes a pressure rise and pushes the gases though the nozzle, resulting in a hot jet that would ignite the lean mixture in the main chamber. Simultaneous high-speed Schlieren photography and OH* Chemiluminescence were applied to visualize the jet penetration and the ignition processes inside the main chamber. Hot Wire Pyrometry (HWP) was used to measure temperature distribution of the transient hot jet. A novel velocity measurement technique based on Schlieren PIV (SPIV) has also been developed to characterize the local flow field. Three nozzle geometries (straight, convergent and converging-diverging) have been studied to understand their effect on ignition probability and characteristics. The results show that a supersonic jet by using a converging-diverging nozzle can ignite leaner mixtures than the jet produced by a straight nozzle of the same throat area (e.g., the ignition limit is reduced to ϕ = 0.22, from 0.35). Additionally, infrared imaging and OH* Chemiluminescence indicated diamond shock structures in the supersonic jets and a high-temperature zone downstream the shocks. This high-temperature zone is likely the reason why the main-chamber flammability limit can be further reduced. Lastly, combustion instability becomes noticeable near the lean-limit conditions for all three types of nozzles, which affect the structural integrity of the combustion chamber. Two instable frequency modes, natural frequency of the combustor at 180 Hz and a higher mode at 2400 Hz were observed.

1 October 2018 in Applied Energy
Verified
Journal Article
Closed access
SBSayan Biswas
Sayan Biswas
LQLi Qiao
Li Qiao

5 October 2017 in SAE International Journal of Engines
Verified
Journal Article
Closed access
PDF file
SBSayan Biswas
Sayan Biswas
LQLi Qiao
Li Qiao
Gas engines often utilize a small-volume pre-chamber in which fuel is injected at near stoichiometric condition to produce a hot turbulent jet which then ignites the lean mixture in the main chamber. Hot jet ignition has several advantages over traditional spark ignition, e.g., more reliable ignition of extra-lean mixtures and more surface area for ignition resulting in faster burning and improved combustion burn time. Our previous experimental results show that supersonic jets could extend the lean flammability limit of fuel/air mixtures in the main chamber in comparison to subsonic jets. The present paper investigated the characteristics of supersonic hot jets generated by combustion of stoichiometric H2/air in a pre-chamber to understand the ignition mechanism of ultra-lean mixtures by supersonic hot jets. Numerical simulations were carried out to examine the transient hot jets issued from six different nozzles (two straight nozzles, one converging nozzle, and three converging-diverging (C-D) nozzles) using a detailed H2/air chemistry. The detailed flame propagation process inside the pre-chamber was investigated. Then the characteristics of the hot jets from six nozzles were compared, including the spatial and temporal distribution of velocity, vorticity, pressure, turbulence quantities, temperature, shock structures, and species concentrations. The results show that supersonic jets exhibit shock diamond structures. The static temperature rises after each shock and a significant temperature rise occur after the final shock. The location of this high-temperature zone is consistent with the experimental observations where ignition was initiated. The profile of Damköhler numbers based on the local flow properties was determined. A critical Damköhler number was found to be 11, below which the main chamber ignition would unlikely to occur. Additionally, the Damköhler number profiles help to explain why the two C-D nozzles with an area ratio of 4 and 9 could extend the flammability limit, whereas the C-D nozzle with an area ratio of 16 failed to do so.

1 November 2017 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
STSaad Tanvir
Saad Tanvir
SBSayan Biswas
Sayan Biswas
LQLi Qiao
Li Qiao