5 July 2022 in IEEE Internet of Things Journal
With the development of economy, the construction of modern infrastructures has been gradually improved. Some infrastructures, such as factories and airports, have large construction volume and high security requirements. Once an intrusion occurs, it will pose a great threat to the safety of personnel and property. Therefore, the perimeter security system based on Internet of Things (IoT) devices and technology is important. Distributed optical fiber sensor (DOFS) is an emerging infrastructure for IoT. Owing to multipoint sensing at the same time, it has attracted extensive attention in the field of perimeter security. However, with the ambient interference, intrusion signals and ambient signals form mixed signals, which brings great difficulty to the efficient and correct identification of intrusion signals. In order to establish a perimeter security system in complex environment, this article proposes an intrusion detection scheme based on DOFS, IoT, and pattern separation technology. The scheme realizes the separation of ambient signals and intrusion signals for the first time. Experiments have proved that this method can separate and recover intrusion signals from mixtures with the average SDR and SI-SDR of 12.35 dB and 11.61 dB, which effectively lays a foundation for subsequent feature extraction and identification. Besides, the response time is only about 0.5 s. This work makes a significant step toward achieving high performance of the perimeter security system in complex environment.
30 October 2023 in Journal of Lightwave Technology
Frequency-modulated continuous-wave (FMCW) lasers are the key components in FMCW LiDAR systems. In this paper, we develop and implement a rapid linearization algorithm to adaptively pre-distort the injection current, we manage to reduce the residual nonlinearity of the triangular-waveform modulated frequency down to $5.4 \times 10^{-9}$ and $4.1 \times 10^{-9}$ for down- and up-ramp frequency sweeping, respectively. The relative residual nonlinearity for down- and up-ramp frequency sweeping are 0.0020% and 0.0017%, respectively. We use this FMCW laser source with high linearity to implement a LiDAR system. We showcase three-dimensional imaging with the depth contrast and the measurement of the distance and velocity, simultaneously, of a moving object.
8 June 2022 in IEEE Transactions on Instrumentation and Measurement
As one of the important sensing technology, tactile sense has been the focus of attention in recent years. Because of its small, light, and anti-electromagnetic interference, fiber Bragg grating (FBG), as an advanced tactile sensor, can be encapsulated on any type of industrial manipulator. Based on the 3-D characteristics of the grabbed object, this article designs a three-fingers FBG tactile sensing system. The structure of wavelength-swept optical coherence tomography is built to collect high sensitivity three-channels FBG tactile sensing signal. The obtained tactile signal is 1-D small volume data, which has fast transmission rate and occupies a small bandwidth. The system is suitable for application in any places especially in industrial with complex environment and precious bandwidth. FBG tactile signal is demodulated into a time-correlation sequence representing the grasping process as the input of neural network. The classification results of two neural networks for processing time-correlation signal, such as WaveNet and long short-term memory (LSTM), are compared. For three channels of the obtained tactile signal, a squeeze-and-excitation module, which increases the correlation between channels, is added to the better performance LSTM model. The accuracy of classification is further improved. The squeeze-and-excitation LSTM (SE-LSTM) classification result shows that the classification accuracy of SE-LSTM for six types of objects with similar size and shape reaches 95.97%, which proves the effective of FBG tactile sensing technology for object classification. The time of single recognition can reach 1.2 ms, which meets the requirements of real time.
25 February 2022 in Journal of Lightwave Technology
A method for simultaneous measurement of static strain and dynamic vibration with high spatial resolution based on millimeter sized ultra-short fiber Bragg grating (FBG) is proposed and experimented in this paper. Dual-parameter can be measured on the single unit of cascaded FBGs, which interrogate with optical coherence tomography method by a designed wavelength swept light source. In experiments, the sensing units were precisely located with mm degrees by inverse FFT of coherent signals and the phase difference calculation. And also the strain and vibration could be simultaneously measured in time and frequency domain: demodulating strain with low frequency component’s phase shift of coherent signals by extracting envelope and interpolation; demodulating vibration by finding peak positions of sidebands in FFT spectrum. Spatial resolution of positioning can reach 0.77 mm. Sensitivity of strain measurement reaches 0.811 $\boldsymbol{\times} 10^{-3} rad/\mu \varepsilon $ under a wavelength sweep rate of 0.2 nm/ms, and forces of several milli newtons can be perceived. The measurement accuracy of kHz vibration frequency is over 98%. Moreover, by comparing simultaneous and respective measurement of dual-parameter, it can be seen that there is almost no crosstalk affectting the results. The results shows great application potential in the field of mechanical sensing, especially in bionic tactile sensing for its simultaneous dynamic and static measurement with accurate positioning performance.
24 June 2021 in IEEE Transactions on Instrumentation and Measurement
In low-frequency vibration measurement field, optical dynamic 3-D measurement based on camera-projector system is a novel approach. In this system, linear sinusoidal grating is the most common projection mode, which can meet the requirements of some vibration measurement. However, the dynamic measurement range of amplitude using the combination of linear grating and Fourier transform profilometry (FTP) is limited in some vibration measurement environments, because the linear fringe is periodic. To solve the problem, this article proposes a low-frequency vibration measurement method based on the concentric-circle grating camera-projector system and FTP. The center of the circle is traced dynamically and the coordinate system is transformed with the center of the circle as the origin. The phase distribution of concentric-circle grating is obtained by coordinate system transformation and FTP. By exploring the relationship between phase and relative height, the time-varying curve of the object surface height is recovered, which contains the vibration information. The experiments compare the measurement ability of the concentric-circle and linear grating. The results show that the linear grating and concentric-circle grating with the similar amplitude resolution have different amplitude measurement range. In this experiment, the maximum measurement range of linear grating is about 2.4 mm, while that of concentric-circle grating is more than about 3.9 mm. It means that the concentric-circle grating projection method can measure a large dynamic range of amplitude under the condition that the center of the circle can be traced, and solve the problem of amplitude limitation of linear grating in the use of FTP.
7 August 2017 in IEEE Photonics Technology Letters
Frequency modulation continuous wave (FMCW) lasers are key components in modern optical imaging. However, current intracavity modulation lasers do not exhibit low-frequency jitter rate and high linearity due to the inherent relaxation oscillations. Although this may be compensated in a direct modulation laser diode using an optoelectronic feedback loop, the available sweep speed is moderately small. In this letter, a special external modulation method is developed to improve the performance of FMCW. Since only the first sideband optical field is used during the entire generation process, phase noise is kept to a minimum and is also independent of the sweep speed. We demonstrate that the linearity and jitter rates do not deteriorate appreciably when the sweep speed is changed over three orders of magnitude, even up to the highest sweep speed of 2.5 GHz/μs.