Xiao Yu

Xiao Yu

Auto-generated profile, based on publicly available information

Xiao Yu

Department of Mechanical Engineering, University of Windsor, Windsor, ON, Canada

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Combustion and Flame
Verified
Journal Article
Closed access
CYChang Ye
Chang Ye
XLXuesong Li
Xuesong Li
XYXiao Yu
Xiao Yu
MZMing Zheng
Ming Zheng
MXMin Xu
Min Xu

1 May 2022 in Plasma Sources Science and Technology
Verified
Journal Article
Open access
PDF file
XYXiao Yu
Xiao Yu
LWLinyan Wang
Linyan Wang
SYShui Yu
Shui Yu
MWMeiping Wang
Meiping Wang
MZMing Zheng
Ming Zheng
In this paper a radiofrequency oscillating plasma discharge is investigated under various initial pressures up to 5 atm in a constant-volume combustion chamber. The oscillating plasma is suppressed by elevated pressure, both in length and branch number. The ignition performance under elevated background pressure is investigated, and the results are compared with spark events with a similar ignition energy. Under ambient conditions, the oscillating plasma discharge generates multiple streamers that are much longer than a spark gap, resulting in a much bigger initial flame kernel. Under elevated background pressures, fewer streamers with much smaller sizes are observed, thus the advantage of an oscillating plasma discharge over a spark discharge is compromised. Prolonged duration of an oscillating plasma discharge consistently demonstrates a positive impact on flame propagation speed, but neither prolonged duration nor enhanced discharge current has a noticeable impact on flame kernel growth for the spark ignition cases. Both oscillating plasma and spark are used to treat non-combustible propane–air mixtures under background pressures from 1 to 5 atm.

7 June 2022 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Open access
XYXiao Yu
Xiao Yu
SLSimon LeBlanc
Simon LeBlanc
NSNavjot Sandhu
Navjot Sandhu
JTJimi Tjong
Jimi Tjong
MZMing Zheng
Ming Zheng
To realize the potential of DME for clean combustion, fueling control is essential. In this research, the challenges, advantages, and applicability of high-pressure direct injection and low-pressure port injection are reviewed and evaluated, especially in relevance to HCCI combustion. In this study, emphasis is given to the applicable ranges of low-pressure fuel delivery in relevance to load, air-fuel ratio, and inert gas dilution, for realizing HCCI combustion. The strategy of high-pressure direct injection is advantageous for combustion phasing control, but the fuel handling is challenging because of the high vapor pressure of DME fuel. The strategy of port fuel injection is prone to early combustion and, consequently, tends to produce excessive pressure rise rates in the combustion chamber. This challenge is escalated at higher engine loads, making homogenous charge compression ignition difficult to achieve. In this paper, the load extension of DME-fueled HCCI combustion was explored. First, the impact of dilution on the combustion characteristics of DME HCCI was studied under lean and CO 2 diluted conditions. Under the present empirical setups, results show that the lean-burn strategy has limited capability of combustion phasing control, especially when the engine load is above 5 bar IMEP. The CO 2 dilution strategy can significantly retard the combustion phasing until the fulfillment of combustion becomes unstable. It was found that spark assistance is advantageous for combustion control. With an effective application of excess air, intake CO 2 dilution and spark assistance, an engine load of 8 bar IMEP was reached with appropriate combustion phasing, with ultra-low NO x emissions.

13 August 2018 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
SDShouvik Dev
Shouvik Dev
TGTongyang Gao
Tongyang Gao
XYXiao Yu
Xiao Yu
MIMark Ives
Mark Ives
MZMing Zheng
Ming Zheng
Homogeneous charge compression ignition (HCCI) has been considered as an ideal combustion mode for compression ignition (CI) engines due to its superb thermal efficiency and low emissions of nitrogen oxides (NOx) and particulate matter. However, a challenge that limits practical applications of HCCI is the lack of control over the combustion rate. Fuel stratification and partially premixed combustion (PPC) have considerably improved the control over the heat release profile with modulations of the ratio between premixed fuel and directly injected fuel, as well as injection timing for ignition initiation. It leverages the advantages of both conventional direct injection compression ignition and HCCI. In this study, neat n-butanol is employed to generate the fuel stratification and PPC in a single cylinder CI engine. A fuel such as n-butanol can provide additional benefits of even lower emissions and can potentially lead to a reduced carbon footprint and improved energy security if produced appropriately from biomass sources. Intake port fuel injection (PFI) of neat n-butanol is used for the delivery of the premixed fuel, while the direct injection (DI) of neat n-butanol is applied to generate the fuel stratification. Effects of PFI-DI fuel ratio, DI timing, and intake pressure on the combustion are studied in detail. Different conditions are identified at which clean and efficient combustion can be achieved at a baseline load of 6 bar IMEP. An extended load of 14 bar IMEP is demonstrated using stratified combustion with combustion phasing control.

5 April 2016 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
SYShui Yu
Shui Yu
Kelvin Y. XieKelvin Y. Xie
Kelvin Y. Xie
XYXiao Yu
Xiao Yu
XHXiaoye Han
Xiaoye Han
LLLiguang LI
Liguang LI
MZMing Zheng
Ming Zheng
Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis. The capacitance paralleled to the spark gap and the in-line resistance installed in the capacitive discharge loop are varied to produce different levels of breakdown enhancement. The burnt fraction and the ignition success rate of the premixed methane-air mixtures are analyzed to evaluate the ignitability improvement. The results indicated that the increase of the capacitance can increase the discharge current and the transient power. It is observed that the voltage buildup rate decreased because of the addition of the capacitor. Different to the conventional peaking capacitor ignition techniques, which normally employ non-resistor spark plugs, the high-power capacitive discharge ignition described in this paper employed an in-line resistor to lower the transient discharge current which might lower the electromagnet interference associated with the high-power capacitive discharge. With a 200pF parallel capacitance, the addition of a 50Ω resistance cuts off 27% peak discharge current compared with a conventional non-resistor case while maintains a same lean ignitable boundary under low pressure experiment conditions.

9 April 2024 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
BCBinghao Cong
Binghao Cong
SLSimon Leblanc
Simon Leblanc
XYXiao Yu
Xiao Yu
MZMing Zheng
Ming Zheng
The majority of transportation systems have continued to be powered by the internal combustion engine and fossil fuels. Heavy-duty applications especially are reliant on diesel engines for their high brake efficiency, power density, and robustness. Although engineering developments have advanced engines towards significantly fewer emissions and higher efficiency, the use of fossil-derived diesel as fuel sets a fundamental threshold in the achievable total net carbon reduction. Dimethyl ether can be produced from various renewable feedstocks and has a high chemical reactivity making it suitable for heavy-duty applications, namely compression ignition direct injection engines. Literature shows the successful use of DME fuels in diesel engines without significant hardware modifications. The lower energy density of DME calls for adjustments in injection parameters (such as injection pressure and duration) or modifications to the injector geometry to align with the energy levels found in diesel fuels. However, detailed direct comparisons between diesel and DME fuel injection characteristics over a wide testing range is lacking.This study investigates the injection characteristics of DME and diesel fuels in a common rail fuel injection system using the Bosch tube method. It is demonstrated that this method can be effectively applied to measure DME fuel injection characteristics, albeit with some limitations in predicting injector closing delay. The research emphasizes the presence of hydraulic delay, resulting in a ratio of actual to commanded injection duration for DME between 1.5 to 2 under the testing conditions. The study finds that mass-based injection quantities for diesel and DME fuels are quite similar at matching conditions, although the lower heating value of DME results in lower energy-based injection quantities and thus fuel injection scheduling need to be adapted to compensate that. Furthermore, the paper offers valuable insights and suggestions for those considering the modification of diesel-operated engines into DME-operated engines.