11 March 2020 in IEEE Transactions on Industrial Electronics
In order to allow a wireless power transfer system to operate in a large-scale space where coupling coefficient has a significant variation due to different air gaps and displacements, a double-side self-tuning LCC /S system using a variable switched capacitor based on parameter recognition is proposed in this article. The main innovation is that the parameter recognition method is able to recognize both mutual inductance and double-side self-inductance with only rms value of sampling signal, phase information and auxiliary circuit being needless. Besides, based on the result of parameter recognition, the double-side use of variable switched capacitors and corresponding control strategy allow the proposed system to operate in a large-scale coupling space and help to improve system efficiency. Experiment results show parameters recognizing error less than 5%. A contrastive simulation verifies that variable switched capacitor can be equivalent to discrete capacitor with the same branch current in the proposed system. System feasibility is testified by a 700-W prototype and the effectiveness of the proposed system is demonstrated by a contrastive experiment with and without pulsewidth modulation (PWM) tuning, efficiency from dc to dc will increase about 3% with PWM tuning.
19 May 2022 in IEEE Transactions on Power Electronics
The double-sided inductor capacitor capacitor topology has been proposed in some national standards for wireless charging systems. However, misalignment between the transmitting and receiving coils usually leads to detuning and weak coupling, resulting in low output power and inefficiency. To improve power output under weak coupling, this article proposes a control method based on the variable inductor and capacitor (VLC). First, it is deduced that the zero phase angle input and full output power can be achieved by VLC regulation under certain misalignment. Second, the variable inductor using an EE-shaped core and pulsewidth modulation controlled capacitor are applied to achieve VLC regulation, and the principles and implementation of VLC are analyzed. Third, as the coupling coefficient k can be identified through the primary electrical parameters, a convenient and accurate coupling coefficient identification method is utilized to help VLC regulation. Finally, a prototype with a 3.3 kW output power and an 87.5% maximum system efficiency (dc–dc) is built to validate the proposed method. The experimental results are consistent with the theoretical analysis, proving that the output power is almost constant when k varies from 0.08 to 0.18.
18 October 2022 in IEEE Transactions on Industrial Electronics
Dynamic wireless power transfer (DWPT) system is applied to electric vehicles, medical treatment, communication, and many other fields. Usually, a dc–dc converter is cascaded at the receiver side to suppress output fluctuation caused by mutual inductance change in the moving process. However, there occurs instability in some conditions in the system under conventional topology and control method. This work proposes a new control method based on a dual buck–boost converter to handle the abovementioned two problems at the same time. It can, in theory, reduce the peak–peak and average values of dc inductor current, meanwhile, increasing the converter efficiency. Also, it can improve the stability margin of the whole system. In this article, we use a simulator to replace the actual DWPT system. Through the simulator, the WPT system can produce the same fluctuating output voltage as that under dynamic conditions to support experiment. The stability of the system is explored by constructing the small-signal model of the system. Then, the effectiveness of the method is proved by simulation and experimental results.
5 October 2021 in IEEE Transactions on Industrial Electronics
In this article, fundamental harmonic analysis (FHA) model is widely used for wireless power transfer due to its physical insight and compact form (for example, 8 RL /π 2 ) of diode rectifier equivalent resistance. Because this compact form is valid for continuous conduction mode (CCM), and resonant tank parameters, such as inductance and capacitance, are independent of equivalent resistance, when designing these parameters based on double side LCC FHA model, the selected optimal parameters may not satisfy the CCM prerequisite. This will make actual system characteristics deviate from the FHA model predictions, especially the output voltage and power. Therefore, the original optimal design is invalid, and designer needs to execute a circular design, namely designing resonant tank parameters based on the FHA model, then judging or simulating whether satisfy CCM operation, redesigning parameters if not satisfy CCM. In order to validate the original optimal design even if CCM is not established and make design process straightforward, an effective remedy, which is adding a series LC filter in secondary side, is proposed, and a computational method about the required minimum filter parameter is provided. The effectiveness of the proposed remedy is verified by simulation and experiment. Besides, the computational method is packaged as a program to help researchers design rapidly.
14 December 2015 in Advanced Science
A novel generalizable strategy is proposed by Y. Yu and co‐workers in article 1500200 for fabrication of a 3D porous interconnected metal sulfide/carbon nanocomposite by the electrostatic spray deposition technique. Such a technique is simple but versatile and can be easily applied to other compounds. The obtained SnS/C composite exhibits a high reversible capacity, high rate capability and long cycling stability for both lithium and sodium storage.
1 January 2023 in Journal of Physics: Conference Series
Electro-fusion welding is a common method for high-density polyethylene (HDPE) pipes. It has a high degree of automation and mature technology. However, during the welding process, various buried defects are easily generated. In this paper, HDPE pipes with welding defects were processed, and X-ray technology was used to detect the defects. The results show that: The X-ray detection technology is sensitive to the defects of sockets and ultralight clay-filled holes. But it is difficult to distinguish the size of the holes. Unfilled holes are partially fused during the welding process, which makes them difficult to detect. In addition, the defects of cold-welding and unscratched oxide skin cannot be detected.