Haibin Tan

Haibin Tan

Auto-generated profile, based on publicly available information

Haibin Tan

Hebei Science and Technology Innovation Service Center, Shijiazhuang 050051, China

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 February 2022 in Water
Verified
Journal Article
Open access
PDF file
DCdongyu cai
dongyu cai
MSMuhammad Rizwan Shoukat
Muhammad Rizwan Shoukat
YZYudong Zheng
Yudong Zheng
HTHaibin Tan
Haibin Tan
FMFanyu Meng
Fanyu Meng
Haijun YanHaijun Yan
Haijun Yan
The dry-hot wind climate is one of the major agro-meteorological disasters associated with high temperature, low humidity, and specific wind forces, which seriously affects the yield of wheat in the North China Plain. A field experiment was conducted to investigate the field microclimate, net photosynthetic rate, chlorophyll content of flag leaves, grain filling rate, and wheat yield after sprinkler misting under the condition of a dry-hot wind climate in the 2018 and 2019 seasons. Two travel speeds, full and half speed, and the corresponding irrigation amounts of 2.5 and 5 mm were used by a center pivot irrigation system during dry-hot wind conditions. A treatment without irrigation was applied as a control. The results showed that the air temperature and relative air humidity were greatly improved within 60 min after irrigation, especially in the upper part of the canopy. The net photosynthetic rate of flag leaves under 5 mm irrigation was higher than that under 2.5 mm irrigation during the middle and late grain filling periods. The adverse effects of dry-hot wind on the chlorophyll content of the flag leaves were mainly concentrated in the late grain filling stage. In the two years of the experiment, the average 1000-grain weights of 5 and 2.5 mm of irrigation treatments were 4.3 and 2.8% higher, and the grain yields were 5.8 and 3.3% higher, respectively, than those of the non-irrigated yields. Overall, applying a small amount of water between 12:00–14:00 with a center pivot before the occurrence of dry-hot wind is an effective means to regulate the field microclimate and produce more yield in the North China Plain.

19 May 2023 in Water
Verified
Journal Article
Open access
PDF file
DCdongyu cai
dongyu cai
MSMuhammad Rizwan Shoukat
Muhammad Rizwan Shoukat
YZYudong Zheng
Yudong Zheng
HTHaibin Tan
Haibin Tan
MSMengyao Sun
Mengyao Sun
Haijun YanHaijun Yan
Haijun Yan
High efficient nitrogen (N) application method and proper N management strategies can further reduce the losses and enhance N use efficiency. Field experiments were conducted in the 2015–2016 and 2016–2017 growing seasons to evaluate the effects of four fertigation frequencies treatments (FT-1: all the topdressing N was applied at the jointing stage; FT-2: 67% and 33% of the topdressing N was applied at the jointing and filling stages; FT-3: 33%, 50% and 17% of the topdressing N was applied at the regreening, jointing and filling stages; FT-4: 33%, 33%, 17% and 17% of the topdressing N were applied at the regreening, jointing, anthesis and filling stages) on wheat yield, water use efficiency (WUE), partial productivity of N fertilizer (PFPN) and N harvest index (NHI). In addition, one-time topdressing by surface broadcasting at the jointing stage was set up as a control (BC-1). The results showed that FT-3 and FT-4 supplied sufficient NO3−-N in the 0–40 cm soil layer, which reduced the risk of soil NO3−-N leaching to the deeper layers. FT-4 had the highest grain yield, WUE, PFPN and NHI, with average values of 9153.4 kg ha−1, 2.1 kg m−3, 0.74 kg kg−1 and 31.3 kg kg−1, respectively, followed by these values corresponding to the FT-3 in two years. These findings suggest that topdressing N split with 3–4 times, that is to say applying approximately 16.7% of topdressing N in anthesis and filling stages, respectively by the center pivot fertigation method can significantly improve yield, WUE, PFPN and NHI.

15 October 2022 in Water
Verified
Journal Article
Open access
PDF file
XWXiaoshan Wang
Xiaoshan Wang
YXYuncheng Xu
Yuncheng Xu
Haijun YanHaijun Yan
Haijun Yan
HTHaibin Tan
Haibin Tan
LZLingjiu Zhou
Lingjiu Zhou
The spraying width and uniformity coefficient are important for the design of a micro-sprinkling hose. In this study, experiments were conducted on the water application intensity distribution for an individual orifice and multiple groups of orifices under three different working pressures (41, 69 and 103 kPa). In the test of an individual orifice, the spraying angles varied from 40° to 90°. The results showed that the water application intensity distributions of an individual orifice were well fitted by a two-dimensional Gaussian distribution. Further study indicated that the bimodal Gaussian distribution model performed well on tracking the two-dimensional features of the water application intensity distribution, with the determination coefficient R2 > 0.90 and the standard root mean square error NRMSE < 30%. It was revealed that the fitting parameters of the two-dimensional Gaussian distribution model had physical meaning and were directly related to the strength and location of the water application intensity distributions. Based on the analysis of these fitting parameters, it was found that the water application intensity distribution of an individual orifice was affected by the pressure, spraying angle and orifice area, among which the spraying angle was the most sensitive factor. By establishing a linear relationship between the fitting parameters and the spraying angles, the water application intensity distribution of an individual orifice for any spraying angle could be predicted by the Gaussian model. Therefore, the water application intensity distribution of multiple groups of orifices could be calculated by overlapping the water application intensity distributions of the individual orifices. The Monte Carlo method was used in this study to determine the maximum spraying width and uniformity coefficient by generating different groups of orifice arrangement for micro-sprinkling hoses. Eventually, the optimized orifice arrangement was recommended for the better design of micro-sprinkling hoses.