26 June 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper proposes an implementation-friendly maximum-minimum-eigenvalue (MME)-based spectrum sensing algorithm for cognitive radio network. An iterative power method has been applied for the first time to compute maximum and minimum eigenvalues that reduces the computational complexity of this MME algorithm. We suggest new digital architecture of MME-based spectrum sensor with shorter critical-path delay that lowers its sensing time. This spectrum-sensor architecture has been resource shared to further enhance the hardware efficiency. Performance analysis of the suggested MME algorithm with 1024 input-signal samples delivers adequate performance at -10 dB of SNR with the detection probability of 0.8. Suggested MME algorithm performs better than the energy detection-based spectrum sensing under noise uncertainty. It has detection gain of 5.3 dB compared to the cyclostationary feature detection-based spectrum sensing algorithm at 0.7 detection probability. Hardware prototyping of our MME spectrum sensor has been carried out in FPGA platform and its real-time testing is performed using the communication environment of DVB-T standard. We synthesized and post-layout simulated proposed digital sensor in 90 nm-CMOS process that resulted in 0.42 mm² of area, operating at a maximum clock frequency of 404 MHz which results in the sensing time of 53.5 μs. Comparison of our work with literature shows that the suggested MME spectrum-sensor has 2.5x shorter sensing time and lowest area-time-product of 0.023, indicating better hardware-efficiency, than the state-of-the-art implementations.
2 September 2022 in IEEE Transactions on Vehicular Technology
This article proposes a simplified offset min-sum (SOMS) decoding algorithm for the QC-LDPC codes. It is an implementation-friendly algorithm based on a new logarithmic-likelihood-ratio (LLR) grouping technique that alleviates the computational complexity of the QC-LDPC channel-decoder. This work also presents a parallel and hardware-efficient architecture of the QC-LDPC decoder based on the suggested SOMS algorithm. Additional architectural transformations have been carried out to reduce the routing complexity of the proposed decoder and deliver lower latency and higher throughput. Comprehensive performance analysis of the SOMS algorithm has been presented under various scenarios based on the specifications of the 5G-NR standard. It shows that the suggested SOMS algorithm delivers an adequate FER of 10 $^{-5}$ at SNR of 1.3 dB while decoding 16-QAM modulated QC-LDPC code with the code rate of 1/3 and the code length of 26112 bits. Subsequently, our QC-LDPC decoder has been hardware-implemented on the FPGA platform (Xilinx Zynq-Ultrascale+ board) that operates at the maximum clock frequency of 128.36 MHz. It can be reconfigured to support seven different 5G-NR code lengths and code rates that range between 10368 $-$ 26112 bits and 1/3 $-$ 8/9, respectively. This FPGA implementation of the proposed QC-LDPC decoder delivers a peak throughput of 13.3 Gbps and latency of 0.77 $\mu$ s while decoding with 10 iterations. On comparing this work with the reported implementations, the proposed decoder has shown 7.5× higher throughput and 34% better hardware efficiency than the state-of-the-art implementations.
28 October 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents implementation friendly VLSI-algorithms for maximum-eigenvalue-detection (MED), energy with minimum-eigenvalue (EME), and mean-to-square extreme-eigenvalue (MSEE) based blind spectrum sensing algorithms. We propose to use efficient iterative power-method for computing maximum and minimum eigenvalues for these algorithms that complemented our hardware design. New VLSI architectures based on suggested spectrum sensing algorithms have been presented in this work. We present two types of sensor architectures: (1) memory-less & low-latency (2) memory-based & resource-shared spectrum-sensor architectures. Former type targets to achieve lower sensing time with adequate hardware efficiency and the later ones are highly resource shared to consume lesser hardware with moderate sensing time. Performance analyses of suggested MED, MSEE and EME spectrum sensing algorithms in AWGN environment showed that the detection probability of 0.75 could be achieved at the SNRs of -12 dB, -10 dB and -7 dB respectively. On synthesizing and post-layout simulating our sensor architectures in 90 nm-CMOS process with the supply of 1.2 V, they could operate at the maximum clock frequency up to 408 MHz delivering sensing time in the range of 23-44 μs. The proposed spectrum sensors have achieved 5.5x and 19x better sensing time and hardware efficiency, respectively, compared to the state-of-the-art implementations. Eventually, the memory-based spectrum sensors are FPGA prototyped and tested, at 100 MHz clock frequency, in DVB-T signal environment with OFDM modulated transmitted signals in 2K size IFFT-mode.
9 October 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief presents an area-efficient technique for the cooperative spectrum sensing (CSS) in data fusion based cognitive radio network. Subsequently, we propose resource-shared and scalable architecture of cooperative spectrum sensor (CSR) by using such technique. It is capable of collectively processing the received signals from six secondary users to reliably detect the spectrum occupancy by primary user. Performance analysis using 16-QAM modulation under fading channel environment indicated that suggested area-efficient based CSS algorithm outperformed the stand-alone spectrum sensing algorithm by 9.45 dB at 0.5 detection probability with a false alarm rate of 0.1. Furthermore, FPGA prototyping of the proposed CSR and its functional validation using real-world hardware test-setup are presented here. Additionally, this CSR architecture has been ASIC synthesized and post-layout simulated in UMC 90 nm-CMOS process. Hence, it occupies 2.47 mm of area, consumes 32 mw of total power at a maximum clock frequency of 101 MHz and delivers an area-efficiency of 0.024 mm-μs. Comparison results have shown that the proposed CSR occupies 63% lesser area and is 47% area-efficient than the conventional implementation.
18 February 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a hardware-friendly algorithm and architecture for cooperative spectrum sensing (CSS) in the data-fusion-based cognitive-radio (CR) network. The proposed VLSI-algorithm is based on the iterative power method and deflation technique that alleviate the computational complexity of conventional CSS algorithm with minimal performance degradation. In this work, a new hardware-efficient VLSI architecture of cooperative spectrum sensor (CSR) for the data-fusion center is presented, which supports up to six secondary users in the cooperative CR network. Its performance analysis under fading channel environment has been carried out where it delivers 0.8 detection probability (Pd) at -8 dB of channel SNR with a false alarm rate of 0.1. It shows the minimum performance degradation of 0.057 dB at Pd = 0.88 compared to the conventional algorithm. The suggested CSR architecture has been application-specific integrated circuit (ASIC)-synthesized and postlayout simulated in UMC 90 nm-CMOS process. Thus, it occupies 2.4 mm² of the core area, consumes 36 mW of total power, and delivers a low sensing time of 60.41 μs while operating at a maximum clock frequency of 87.7 MHz. Comparison with the reported works indicates that the proposed design requires 40.3% lesser area, and it is 41% hardware efficient than the conventional implementation. Eventually, this design has been field-programmable gate array (FPGA) prototyped, and its functionality is verified in the real-world test environment.