In this paper, we present a comprehensive uncertainty budget for on-wafer S-parameter measurements of devices on a custom-built fused silica wafer, including instrumentation errors, connector repeatability, and calibration standard uncertainties. All major steps toward achieving traceability with the aid of a multiline thru-reflect-line calibration for the given measurement scenario are explained. For the first time, it is now possible to compare against each other the relative importance of different sources of uncertainty in on-wafer measurements. Results are shown for three typical devices with varying reflection and transmission characteristics.
The millimeter-wave (mm-wave) and terahertz (THz) regions of the electromagnetic spectrum are seeing increasing prominence, with a range of established and emerging applications—wireless backhaul for mobile networks for 5G and 6G infrastructure, automotive radar sensors, space-deployed radiometers for Earth observation, climate monitoring, weather forecasting, and more—exploiting these frequencies. Measurement techniques informed by the latest metrological research into the measurement of electrical quantities underpin the development of components and circuits for such applications by enabling the accurate and consistent measurement results to be obtained.
11 March 2022 in IEEE Transactions on Instrumentation and Measurement
This article presents the design, fabrication, and characterization of a D-band (110–170 GHz) bolometric power sensor, used for millimeter-wave metrology. This sensor type is new thin-film-based sensor, which consists of a multilayer chip embedded in a silicon substrate as a microwave absorber. The sensor demonstrates reasonable performance with a return loss of better than 15 dB across the entire D-band and the rise and fall times better than 1.8 ms. The sensor achieves high power linearity between −10 and +8 dBm. Frequency response of the sensor was measured, and its flatness changes no more than 20% across the frequency band. Furthermore, this power sensor has been characterized in the microcalorimeter, and an effective efficiency of over 90% could be achieved. For the first time, the design, fabrication, and characterization of a novel power sensor prototype with excellent performance at D-band are presented.
The principle of sequential rotation, a well-known method to arrange the radiating elements of antenna arrays, is briefly described, and the impact on the polarization of different antenna array configurations is presented. The influence of the number of rotations and rotation angles is investigated, and arrangements for optimized polarization quality of antenna arrays are shown, which are of significant importance for current and future communications systems.
28 May 2020 in IEEE Transactions on Instrumentation and Measurement
Two independent methods of absolute power measurement of electromagnetic waves are compared in the millimeter-wave range. At National Metrology Institutes (NMIs), dependent on frequency and wave propagation, electromagnetic power is differently traced back to the International System of Units (SI), i.e. from microwave up to millimeter-wave frequencies in coaxial lines and metallic waveguides, whereas at Terahertz frequencies in free-space. As state-of-the-art waveguide-based power sensors and free-space power detectors are overlapping with respect to their operating frequency, for the first time, a comparison of both independent power scales has been carried out in the millimeter-wave range. The experiment verified the consistency of both traceability approaches within their uncertainties.
14 February 2020 in IEEE Transactions on Applied Superconductivity
To make the experimental set-up of the Josephson Arbitrary Waveform Synthesizer (JAWS) less complex by reducing the number of RF cables between room and cryogenic temperature, we developed on-chip RF power dividers. By integration of these components, we can eventually increase the number of Josephson junctions operated by one single pulse pattern generator channel, and thus reduce the costs of the set-up. At PTB, we designed, fabricated and investigated the performance of two different RF power dividers types: the serial parallel and the Wilkinson power divider. Spectrally pure sinusoidal waveforms were successfully synthesized with both types of power dividers. With the Wilkinson power divider, e.g., we obtained 17.55 mV (RMS) at a clock-frequency of 15 GHz combined with a test array of 1000 Josephson junctions. As for the serial-parallel power divider combined with a test array of 2000 Josephson junctions we synthesized RMS output voltages of 19.0 mV.