7 February 2025 in Inorganic Chemistry
Metal-organic frameworks (MOFs) are promising porous materials for CO2 adsorption due to their high surface area, tunable properties, and selective adsorption capabilities. The recently reported Calgary Framework 20 (CALF-20) MOF has very appealing CO2 capture properties: high uptake capacity; low regeneration energy; durability (>450 000 cycles) under steam and wet acid gases; simple and scalable synthesis. This study investigates the microwave (MW)-assisted synthesis of CALF-20, which reduces reaction time 12-fold while enhancing the synthesis yield to 97%. Structural analysis confirmed that MW-synthesized CALF-20 retains its crystallographic structure and shows improved CO2 capture performance, exhibiting higher adsorption capacity (∼20% higher), selectivity, and lower regeneration energy. This method provides a rapid and efficient alternative for producing the CALF-20 adsorbent for CO2 capture and separation applications.
28 June 2023 in Analytical Chemistry
Additive manufacturingsuch as three-dimensional (3D)-printinghas revolutionized the fast and low-cost fabrication of otherwiseexpensive NMR parts. High-resolution solid-state NMR spectroscopydemands rotating the sample at a specific angle (54.74 & DEG;) insidea pneumatic turbine, which must be designed to achieve stable andhigh spinning speeds without mechanical friction. Moreover, instabilityof the sample rotation often leads to crashes, resulting in costlyrepairs. Producing these intricate parts requires traditional machining,which is time-consuming, costly, and relies on specialized labor.Herein, we show that 3D-printing can be used to fabricate the sampleholder housing (stator) in one shot, while the radiofrequency (RF)solenoid was constructed using conventional materials available inelectronics stores. The 3D-printed stator, equipped with a homemadeRF coil, showed remarkable spinning stability, yielding high-qualityNMR data. At a cost below 5 euro, the 3D-printed stator representsa cost reduction of over 99% compared to repaired commercial stators,illustrating the potential of 3D-printing for mass-producing affordablemagic-angle spinning stators.
12 April 2024 in ACS Omega
This study delves into the potential advantage of utilizing crab shells as sustainable solid adsorbents for CO2 capture, offering an environmentally friendly alternative to conventional porous adsorbents, such as zeolites, silicas, metal–organic frameworks (MOFs), and porous carbons. The investigation focuses on crab shell waste, which exhibits inherent natural porosity and N-bearing groups, making them promising candidates for CO2 physisorption and chemisorption applications. Selective deproteinization and demineralization treatments were used to enhance textural properties while preserving the natural porous structure of the crab shells. The impact of deproteinization and demineralization treatments on CO2 adsorption and speciation at the atomic scale, via solid-state NMR, and correlated findings with textural properties and biomass composition were investigated. The best-performing sample exhibits a surface area of 36 m2/g and a CO2 adsorption capacity of 0.31 mmol/g at 1 bar and 298 K, representing gains of ∼3.5 and 2, respectively, compared to the pristine crab shell. These results underline the potential of fishing industry wastes as a cost-effective, renewable, and eco-friendly source to produce functional porous adsorbents.
1 January 1995 in IEEE Journal of Quantum Electronics
We present the frequency measurements of 14 Far-Infrared (FIR) laser lines. We use the heterodyne technique of mixing FIR laser transitions and microwave radiation on a MIM point contact diode to determine the FIR frequencies. The main motivation was to measure the frequency of laser lines of meterological interest, around the 1.6 and 1.2 THz regions. We also present 15 new FIR laser lines we found while performing the frequency measurements, with wavelengths ranging from 90 mum to 819.2 mum. All of them are characterized in wavelength, polarization, intensity, working pressure and absorption offset
30 September 2025 in ACS Applied Polymer Materials
ASArmando J. D. Silvestre
Biopolymer-based aerogels have emerged as promising CO2 adsorbents for large-scale implementation due to their abundance, renewability, and low cost. However, the CO2 capture mechanisms of these materials remain poorly understood. In this study, we exploit the structural similarity between cellulose and chitosan to investigate how surface chemistry governs the CO2 adsorption mechanisms using a combination of solid-state nuclear magnetic resonance (ssNMR) spectroscopy and density functional theory (DFT) modeling. We reveal that cellulose aerogels adsorb CO2 exclusively via physisorption, whereas chitosan aerogels exhibit both physisorption and chemisorption. Chemical shift analysis, supported by DFT calculations, identifies two chemisorbed species in chitosan: carbamic acid (159.0 ppm) and ammonium carbamate (164.5 ppm). Additionally, ssNMR relaxation measurements reveal three distinct physisorbed CO2 states (solid, liquid, and gas-like) in both aerogels. By systematically tailoring the amine density (i.e., the interchain distance) in chitosan, we elucidate its influence on the CO2 chemisorption speciation. Based on well-established principles of polysaccharide chemistry, we engineered a blended cellulose dialdehyde–chitosan aerogel with reduced amino group density. In this material, only the carbamic acid peak was observed, demonstrating that ammonium carbamate formation requires closely spaced amino groups. These findings highlight the critical role of surface functional groups and amine density in dictating the CO2 adsorption pathways. Our study provides valuable atomic level insights into the structure–function relationships of biopolymer-based sorbents, facilitating their optimized design for CO2 capture technologies.