1 March 2017 in Materials Research Express
7 September 2018 in Materials Research Express
7 August 2019 in Journal of Chemistry
Al-incorporated SBA-15 samples (xAl/SBA-15) were successfully prepared by “atomic implantation” method. The samples were characterized by X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), N2 adsorption-desorption isotherms (BET), and temperature-programmed desorption (NH3-TPD). In this catalyst, metal oxide species were highly dispersed on the SBA-15 surface and existed as isolated atoms. It was shown that the Al incorporation lead to the formation of medium and strong acid sites. The catalytic activity and selectivity were tested in a mild hydrothermal process for degradation of cotton cellulose to 5-hydroxymethyl furfural (5-HMF). A cellulose conversion of 68.5% and 5-HMF selectivity of 62.1% after 2 h of reaction at 170°C were achieved. The very high 5-HMF yield (42.57%) obtained in this paper is much higher than that was reported in the literature.
26 November 2016 in Applied Nanoscience
In this study, we report the direct precipitation of nano-HA in the present of maltodextrins with the different dextrose equivalent (DE) values in the range of 10–30. Characterization of the obtained samples, using X-ray diffraction and Fourier transform infrared spectrophotometry, indicated that the presence of maltodextrins, with the different DE values, does not affect the phase composition and structure of the obtained composites. Morphology studies of the samples, using field emission scanning electron microscope and transmission electron microscope, revealed that maltodextrin has obvious effect on the size, shape, and morphology of hydroxyapatite nanoparticles. In particular, in studied DE range, maltodextrin DE 28–30 with dominant structure of debranched chain is the most preferable choice to obtain the composite with highly dispersed nanoparticles. In vitro assay on pre-osteoblast MC3T3-E1 cells demonstrated the ability of the composites to stimulate alkaline phosphatase activity and mineralization during differentiation of the cells.
10 July 2018 in Journal of Materials Engineering and Performance
1 August 2020 in Journal of Nanomaterials
Catalytic ozonation is a new method used for removal of NH4OH solution. Therefore, high catalytic performance (activity and selectivity) should be achieved. In this work, we report the synthesis and catalytic performance of Fe2O3-Co3O4 modified dolomite in the catalytic ozonation of NH4OH solution. Dolomite was successfully activated and modified with Fe2O3 and Co3O4. Firstly, dolomite was activated by heating at 800°C for 3 h and followed by KOH treatment. Activated dolomite was modified with Fe2O3 by the atomic implantation method using FeCl3 as Fe source. Fe2O3 modified dolomite was further modified with Co3O4 by precipitation method. The obtained catalysts were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), N2 adsorption–desorption (BET), and temperature-programmed reduction (H2-TPR). From SEM image, it was revealed that nano-Fe2O3 and Co3O4 particles with the size of 80–120 nm. Catalytic performance of activated dolomite, Fe2O3 modified dolomite, and Fe2O3-Co3O4 modified dolomite in catalytic ozonation of NH4+ solution was investigated and evaluated. Among 3 tested catalysts, Fe2O3-Co3O4 modified dolomite has the highest NH4+ conversion (96%) and N2 selectivity (77.82%). Selectivity toward N2 over the catalyst was explained on the basis of bond strength M-O in oxides through the standard enthalpy of oxide. Catalyst with lower value has higher N2 selectivity and the order is the following: Co3O4 ( of 60 kcal (mole O)) > Fe2O3 ( of 70 kcal (mole O)) > MgO ( of 170 kcal (mole O)). Moreover, high reduction ability of Fe2O3-Co3O4 modified dolomite could improve the N2 selectivity by the reduction of NO3- to N2 gas.