Anafi Nur’aIni

Anafi Nur’aIni

Auto-generated profile, based on publicly available information

Anafi Nur’aIni

Departments of Applied Chemistry, Chemical Engineering, and Department of Energy Convergence Engineering, Kumoh National Institute of Technology, Gumi, Gyeongbuk 39177, South Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2020 in RSC Advances
Verified
Journal Article
Open access
PDF file
ANAnafi Nur'AIni
Anafi Nur'AIni
IOIlwhan Oh
Ilwhan Oh
Methylammonium lead iodide (MAPbI3) perovskite thin film has been successfully applied to a volatile organic compound (VOC) gas sensor that can operate at room temperature. In this study, ∼100 nm-thick MAPbI3 film shows good reversibility and repeatability as a VOC gas sensor. The resistance of the MAPbI3 film substantially decreases when it is exposed to VOC vapour and recovers back to high resistance when the VOC gas is removed. Adsorption of VOC gas molecules to vacancies in MAPbI3 film might lead to charge trap passivation. The VOC sensor based on perovskite thin film is tested in terms of film thickness, applied bias voltage, and polarity of VOC. We expect that our VOC gas sensor based on solution-processed MAPbI3 operating at room temperature has potential to be developed as a low cost and low power smart gas sensor.

2 May 2022 in ACS Omega
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
IOIlwhan Oh
Ilwhan Oh
A deep etching method for silicon "micro"structures was successfully developed. This wet etching process is based on metal-assisted chemical etching (MACE), which was previously mainly utilized to etch the features that have lateral dimensions of "nanometers." In this novel MACE, the critical improvement was to promote the "out-of-plane" mass transfer at the metal/Si interface with an ultrathin metal film. This enabled us to etch micrometer-wide holes, which was previously challenging due to the mass transport limitation. In addition, it was found that when ethanol was used as a solvent instead of water, the formation of porous defects was suppressed. Under the optimized etch conditions, deep (>200 μm) and vertical (>88°) holes could be carved out at a fast etch rate (>0.4 μm/min). This novel deep MACE will find utility in applications such as microelectromechanical systems (MEMS) devices or biosensors.

26 November 2024 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
ELEmma Laasonen
Emma Laasonen
VRVesa Ruuskanen
Vesa Ruuskanen
TKTuomas Koiranen
Tuomas Koiranen
PKPertti Kauranen
Pertti Kauranen
JAJero Ahola
Jero Ahola

5 January 2025 in Journal of Industrial and Engineering Chemistry
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
ELEmma Laasonen
Emma Laasonen
VRVesa Ruuskanen
Vesa Ruuskanen
TKTuomas Koiranen
Tuomas Koiranen
PKPertti Kauranen
Pertti Kauranen
JAJero Ahola
Jero Ahola

15 July 2025 in Journal of CO2 Utilization
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
ELEmma Laasonen
Emma Laasonen
ACAlireza Charmforoushan
Alireza Charmforoushan
VRVesa Ruuskanen
Vesa Ruuskanen
TKTuomas Koiranen
Tuomas Koiranen
JAJero Ahola
Jero Ahola

19 December 2025 in Energy Conversion and Management
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
ELEmma Laasonen
Emma Laasonen
LJLauri Järvinen
Lauri Järvinen
VRVesa Ruuskanen
Vesa Ruuskanen
TKTuomas Koiranen
Tuomas Koiranen
JAJero Ahola
Jero Ahola