Ilwhan Oh

Ilwhan Oh

Auto-generated profile, based on publicly available information

Ilwhan Oh

Department of Applied Chemistry Kumoh National Institute of Technology Gumi Republic of Korea

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 April 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
SNSeongSik Nam
SeongSik Nam
CMCuc Thi Kim Mai
Cuc Thi Kim Mai
IOIlwhan Oh
Ilwhan Oh

1 April 2020 in RSC Advances
Verified
Journal Article
Open access
PDF file
ANAnafi Nur'AIni
Anafi Nur'AIni
IOIlwhan Oh
Ilwhan Oh
Methylammonium lead iodide (MAPbI3) perovskite thin film has been successfully applied to a volatile organic compound (VOC) gas sensor that can operate at room temperature. In this study, ∼100 nm-thick MAPbI3 film shows good reversibility and repeatability as a VOC gas sensor. The resistance of the MAPbI3 film substantially decreases when it is exposed to VOC vapour and recovers back to high resistance when the VOC gas is removed. Adsorption of VOC gas molecules to vacancies in MAPbI3 film might lead to charge trap passivation. The VOC sensor based on perovskite thin film is tested in terms of film thickness, applied bias voltage, and polarity of VOC. We expect that our VOC gas sensor based on solution-processed MAPbI3 operating at room temperature has potential to be developed as a low cost and low power smart gas sensor.

2 May 2022 in ACS Omega
Verified
Journal Article
Open access
ANAnafi Nur’aIni
Anafi Nur’aIni
IOIlwhan Oh
Ilwhan Oh
A deep etching method for silicon "micro"structures was successfully developed. This wet etching process is based on metal-assisted chemical etching (MACE), which was previously mainly utilized to etch the features that have lateral dimensions of "nanometers." In this novel MACE, the critical improvement was to promote the "out-of-plane" mass transfer at the metal/Si interface with an ultrathin metal film. This enabled us to etch micrometer-wide holes, which was previously challenging due to the mass transport limitation. In addition, it was found that when ethanol was used as a solvent instead of water, the formation of porous defects was suppressed. Under the optimized etch conditions, deep (>200 μm) and vertical (>88°) holes could be carved out at a fast etch rate (>0.4 μm/min). This novel deep MACE will find utility in applications such as microelectromechanical systems (MEMS) devices or biosensors.

12 May 2014 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
YSYunwon Song
Yunwon Song
BKBugeun Ki
Bugeun Ki
KCKeorock Choi
Keorock Choi
IOIlwhan Oh
Ilwhan Oh
JOJungwoo Oh
Jungwoo Oh
We have demonstrated the dependence of the metal-assisted chemical etching of GaAs on catalyst thickness. For ultra-thin (3~10 nm) Au catalysts, we found that electrochemically generated nano-pinholes in the metal catalyst not only enhance important catalytic effects in redox reactions, but also act as a diffusion pathway for the reactants (H2SO4) and products (Ga3+ and Asn+ ions) for chemical etching oxidized GaAs.

28 February 2022 in Journal of Electrochemical Science and Technology
Verified
Journal Article
Open access
PDF file
ANAnafi Nur'AIni
Anafi Nur'AIni
SLSeokwon Lee
Seokwon Lee
IOIlwhan Oh
Ilwhan Oh
Metal halide perovskites are promising photovoltaic materials, but they still have some issues that need to be solved. Hysteresis is a phenomenon that strongly is correlated with ion migration; thus, a fast, easy, and low-temperature method for measuring ion migration is required. Through selective blocking, ion migration can be measured separately, apart from electron migration. In this study, ion migration in metal halide perovskites was measured using a vertical device. At different temperatures, ionic activation energies were obtained for a range of perovskite compositions such as MAPbI3, FAPbI3, CsPbI3, and MAPbBr3. By comparing the measured ionic activation energies with the theoretical values, we conclude that among other possibilities, I− is the migrating ion in MAPbI3, FAPbI3, CsPbI3, and Br− is the migrating in MAPbBr3.

14 November 2018 in Energies
Verified
Journal Article
Open access
PDF file
IOIlwhan Oh
Ilwhan Oh
JCJaeyoung Cho
Jaeyoung Cho
KKKwansu Kim
Kwansu Kim
JKJaehwan Ko
Jaehwan Ko
HCHae-Won Cheong
Hae-Won Cheong
HJHyun Min Jung
Hyun Min Jung
The polymer binder, poly(imide-co-siloxane) (PIS), was synthesized and applied to form a thin cathode layer of composites for a thermal battery that has an unusually high operating temperature of 450 °C. The PIS was prepared through cross-linking of the polyimide with polysiloxane. The morphology of FeS2/PIS composites showed that FeS2 particles was coated with the PIS cross-linked gel. The FeS2/PIS composites enabled to fabricate mechanically stable thin cathode layer that was 10–20% of the thickness of a conventional pellet-type cathode. The FeS2/PIS composites were stable up to 400 °C and maintained their morphology at this temperature. PIS coating layers decomposed at 450 °C, and a new residue was generated, which was observed by transmission electron microscopy, and the compositional change was analyzed. The FeS2/PIS composites showed enhanced thermal stability over that of FeS2 in thermogravimetric analysis. The thermal battery with the PIS polymer binder showed a 20% discharge capacity increase when compared to a conventional pellet-type cathode.