Jan Barta

Jan Barta

Auto-generated profile, based on publicly available information

Jan Barta

Department of Power Electrical and Electronic Engineering, Faculty of Electrical Engineering and Communication, Brno University of Technology, Brno, Czech Republic

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 October 2024 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
PKPetr Klima
Petr Klima
JBJan Barta
Jan Barta
DKDaniel Koutny
Daniel Koutny
OVOndrej Vitek
Ondrej Vitek
High-speed machines are popular in industry due to their high power density. Permanent synchronous machines are commonly preferred, but they rely on rare earth magnets, which are expensive and environmentally demanding. Axially laminated anisotropic synchronous reluctance machines, a promising alternative, are currently limited to two poles and simple rotor geometry. This paper proposes a modified axially laminated anisotropic geometry, produced using multi-material additive manufacturing, to overcome these limitations in a high-speed synchronous reluctance machine. Magnetic 17-4PH and non-magnetic 316L steels were selected as suitable materials for a case study machine. To determine the effect of heat treatment on the magnetic properties of an additively manufactured 17-4PH steel sample, magnetic measurements were conducted. A 60 000-rpm case study machine was optimized using a non-dominated sorting genetic algorithm II, resulting in a machine with a shorter active length. Tests conducted during and after manufacturing verified the feasibility of the proposed rotor solution. This development expands the potential use of axially laminated anisotropic topology and synchronous reluctance machines in high-speed applications. Additionally, the successful use of multi-material additive manufacturing technology in the field of electrical machines is demonstrated.

19 February 2025 in International Journal of Electrical Power & Energy Systems
Verified
Journal Article
Open access
VBVladimir Bilek
Vladimir Bilek
JBJan Barta
Jan Barta
MTMarek Toman
Marek Toman
PLPetr Losak
Petr Losak
Gerd BramerdorferGerd Bramerdorfer
Gerd Bramerdorfer

11 March 2015 in MM Science Journal
Verified
Journal Article
Closed access
JBJan Barta
Jan Barta
COCestmir Ondrusek
Cestmir Ondrusek

13 August 2021 in IEEE Access
Verified
Journal Article
Open access
JBJan Barta
Jan Barta
LKLadislav Knebl
Ladislav Knebl
Gerd BramerdorferGerd Bramerdorfer
Gerd Bramerdorfer
ILIveta Lolova
Iveta Lolova
SSSiegfried Silber
Siegfried Silber
OVOndrej Vitek
Ondrej Vitek
An optimally designed line-start permanent magnet synchronous machine may require a different squirrel-cage design than traditional induction machines. The objective of this paper is to apply topology optimization based on the normalized Gaussian network in order to find the optimal shape of the rotor bars for a line-start permanent magnet synchronous machine. This approach facilitates optimizing the shape of the bar, without the limitation of a predefined bar geometry and arrangement, as is usually considered for classic induction machine design. For this study, a previously designed four-pole line-start permanent magnet synchronous machine with a rated power of 1.5kW is used as an initial design. To verify the accuracy of performance evaluation by utilizing finite-element methods, a prototype of this machine was built and tested. Then, verified model of line-start permanent magnet machine is used for topology optimization of its rotor cage area. The outcome of the optimization is the Pareto front, from which three optimized designs are selected. Finally, these designs are analyzed and proved to have better steady-state performance than the initial machine. The results provide new insights for the design of squirrel-cage bars for line-start permanent magnet synchronous machines.

1 September 2021 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
VAValerii Abramenko
Valerii Abramenko
JBJan Barta
Jan Barta
ILIveta Lolova
Iveta Lolova
IPIlya Petrov
Ilya Petrov
JPJuha Pyrhonen
Juha Pyrhonen
A direct-on-line synchronous reluctance motor (DOLSynRM) with a rotor topology defined by the natural flux line curve approach is studied as an alternative to an induction motor using a 1.5 kW, 50 Hz synchronous reluctance motor as an example. If an induction motor stator is used, a direct squirrel-cage rotor replacement by a synchronous reluctance rotor equipped with a damper winding might not guarantee a sufficient starting performance. To ensure strong enough starting capability, the natural flux line curve approach was modified in the motor design. The proposed approach was applied in the optimization of the DOLSynRM using a genetic algorithm. The optimization results show a clear tendency in the rotor design when trying to achieve a reliable starting capability and to maximize the steady-state performance of the DOLSynRM. Both the stator design and the rotor diameter of the optimized DOLSynRM are different from those of a corresponding squirrel-cage induction motor. A DOLSynRM prototype was built and tested. It showed about a 5.4%-unit higher efficiency than the original prototype of IM and acceptable starting performance under the rated load condition. The starting capabilities of the motors under study are considered with different loads. The locked-rotor apparent power and current stay below permitted limits in both IM and DOLSynRM.

2 February 2021 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
LKLadislav Knebl
Ladislav Knebl
JBJan Barta
Jan Barta
Gerd BramerdorferGerd Bramerdorfer
Gerd Bramerdorfer
OVOndrej Vitek
Ondrej Vitek
COCestmir Ondrusek
Cestmir Ondrusek
This article introduces the design and optimization of line-start synchronous machines in fractional horsepower industry applications. The proposed optimized design will be considered as a replacement for the induction machine driven from an ac drive. The optimized design will be achieved using a 2-D finite-element transient analysis and multi-objective optimization algorithm. For the optimization, a multi-objective self-organizing migrating algorithm was chosen. The optimization results are compared with the more popular nondominated sorting genetic algorithm (NSGA-II) algorithm, to prove algorithm sufficiency with three objectives and five design parameters in the area of the electromagnetic design application.