A high demand for electrification of the transport sector has resulted in a need to provide compact and reliable electric power trains where the electric machine is a key element. The cooling system has a strong impact on the specific torque and power capability of the machine. The selection of the cooling solution should not be based on the steady-state cooling performance only but also on the transient characteristics owing to the typical operational load nature of the propulsion system, where the load is not continuous (as it usually is in industrial applications), but it frequently varies in time depending on the vehicle type and the driving style. This article investigates in detail the cooling capabilities of a direct winding liquid cooling solution and compares it with a traditional frame liquid cooling arrangement in the transient condition. As a result of the comparison, it was found that the location of heat removal close to the heat source makes the temperature transient time faster, which allows to apply overload operating points more frequently.

The performance capabilities of an axially laminated anisotropic rotor (ALA) in a high-speed synchronous reluctance motor (SynRM) were studied. A 12 kW ALASynRM was designed as an alternative to a high-speed induction motor (IM) with a solid rotor. The electromagnetic design was implemented taking into account possible issues related to the new manufacturing methods, which require thicker rotor layers than in a typical ALA. The ALASynRM shows a higher efficiency than the corresponding IM with a smooth or slitted solid rotor equipped with copper end rings. To verify the design method, a prototype IM with a smooth solid rotor was built and tested. In the analysis, it was found that, similar to IMs, in an ALASynRM a considerable part of losses takes place in the rotor despite the absence of slip-related losses in the SynRM. The distribution of eddy current losses in the ALA rotor is significantly uneven. The torque ripple in the ALASynRM is considerably larger than the corresponding ripple in IMs.

High-speed solid-rotor induction machines (HSIMs) are popular within high-speed (HS) applications because of their high rotor structural integrity and their fairly well-established manufacturing process guaranteeing high quality series products. Designing a new HS electric machine requires a multidisciplinary team to accomplish the machine performance desired. In case of a HS machine design, the components and applied materials often reach their physical limits at the rated operating condition. Therefore, the design process is highly iterative and, thus, a systematic approach has a high potential to reduce the time of the design phase significantly. In this article, a systematic design process is proposed for a modular, multimegawatt (MMW) HSIM with three radial active magnetic bearings. The process includes a traditional multidisciplinary design flow with extra critical aspects of MMW HS machines: manufacturability, bearing system, housing, and operating unit. In addition, the manufactured machine is reported. The proposed systematic design process is described, including several multidisciplinary critical design aspects of HS machinery.

Direct liquid cooling (DLC) of electrical machine windings is a clearly effectual cooling method for high-torque and high-power-density applications needed, especially, in heavy vehicles. Usually, in electric vehicles, the stator copper winding losses are the most dominating losses during the accelerating or decelerating (recuperation) modes, and therefore, traditional windings may heat up significantly during high-torque periods. Removing the heat directly from the winding in which most of the heat is generated, allows the most straightforward and effective way of cooling. This paper investigates the feasibility of the direct liquid cooling in a radial-flux permanent-magnet traction motor. This case provides experimental information of the behavior of the direct liquid cooling of the windings. The prototype motor equipped with directly liquid-cooled windings is installed in an electric bus so that typical bus load cycles can be tested.

A novel rotor structure for a tooth-coil-winding (concentrated winding) open-slot axial-flux permanent-magnet (PM) machine that reduces the eddy currents and increases the main flux linkage is proposed in this paper. A composite-body-based rotor assembly and a steel-laminated layer inserted on top of the magnets are used to reduce eddy-current losses in the PMs. A prototype of an axial flux generator for a heavy-duty vehicle following this structure is optimized, analyzed and measured. The tooth coil windings produce high-amplitude harmonics in the air gap and the large slot openings reduce the rotor flux. Consequently, a rotor structure that decreases the amount of harmonics travelling through the magnets is required. Steel laminations covering the magnets have positive effects on both phenomena. Two-dimensional and three-dimensional finite-element analysis is used to verify and optimize the geometry of the laminations. Computations are verified by experimental measurements of a 100 kW test machine prototype.

High-power high-speed induction machines (IMs) are gaining ground in various industrial applications, especially in replacing traditional motors and gearboxes driving compressors or high-pressure pumps, etc. However, the high-speed technology presents extra challenges for the mechanical structure of the machine including bearing systems. Therefore, it is often reasonable to use active magnetic bearings (AMBs) instead of traditional bearings as they provide much smaller friction and allow a not perfectly centered orbit of the rotor without affecting the lifetime of the bearings. Using AMBs in a machine, the nonuniformity of the rotor leads to an inevitable rotor eccentricity; the level of which depends on the control tolerance and dynamic characteristics of the AMB and the maximum force generated by the AMB. This rotor eccentricity results in an unbalanced magnetic pull (UMP) of the rotor, which has to be compensated by the AMB. This paper analyzes the UMPs of a 2 MW, 12 000 r/min IM in the static eccentricity, dynamic eccentricity, and mixed eccentricity conditions. The AMB system was designed and optimized with the consideration of gravity and UMP effects. Furthermore, the required current compensation for the forces in the horizontal and vertical directions was studied during the operation and verified by the finite-element method.