Aqeel Ahsan Khurram

Aqeel Ahsan Khurram

Auto-generated profile, based on publicly available information

Aqeel Ahsan Khurram

NCP Complex

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 September 2014 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
GHGhulam Hussain
Ghulam Hussain
AJAbdul Jabbar
Abdul Jabbar
IQIrfan Qasim
Irfan Qasim
MMM. Mumtaz
M. Mumtaz
KNK. Nadeem
K. Nadeem
AKA. A. Khurram
A. A. Khurram
Silver (Ag) nanoparticles were added into (Cu0.5Tl0.5)Ba2Ca2Cu3O10−δ (CuTl-1223) high Tc superconducting matrix to get (Ag)x/CuTl-1223, x = 0, 0.5, 1.0, 2.0, and 4 wt. %, nano-superconductor composites. The activation energy {U (eV)} and zero resistivity critical temperature {Tc (0)} were increased with increasing contents of Ag nanoparticles in (CuTl-1223) phase up to x = 2.0 wt. %. The increase of activation energy is most probably due to interaction of carriers with the metallic Ag nanoparticles present at grain boundaries of the host CuTl-1223 superconducting matrix. The systematic increase in Tc (0) and gradual decrease in normal state resistivity {ρ300 K (Ω cm)} may be due to improved inter-grains coupling by filling up the voids and pores with the inclusion of metallic Ag nanoparticles at the grain-boundaries. There are two possible mechanisms associated with the inclusion of Ag nanoparticles, one is the formation of non-superconducting regions causing the increase of activation energy and other (dominating) is the improved inter-grains connectivity promoting Tc (0). The microscopic parameters (i.e., zero temperature coherence length along c-axis {ξc (0)}, inter-layer coupling (J), inter-grain coupling (α), etc.) deduced from the fluctuation induced conductivity analysis reasonably explained the experimental findings.

27 May 2012 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
SRSobia A. Rakha
Sobia A. Rakha
RKRamsha R. Khan
Ramsha R. Khan
AKAqeel A. Khurram
Aqeel A. Khurram
AFA. Fayyaz
A. Fayyaz
MZM. Zakaullah
M. Zakaullah
AMArshad Munir
Arshad Munir

1 August 2023 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
HNHammad Nadeem
Hammad Nadeem
NGNuman Ghazali
Numan Ghazali
MNM Nabeel
M Nabeel
MAMn Ahsan
Mn Ahsan
AKAa Khurram
Aa Khurram
The surface roughness assessment of 3D printed parts with Fused Deposition Modelling (FDM) has been performed on Acrylonitrile Butadiene Styrene, Poly Lactic Acid, Polycarbonate, Nylon, Polypropylene, Co-polyester. Three different geometries were selected i.e., Cube, Cone and Strip to evaluate the effect of build geometry and material on the surface roughness of 3D printed parts of FDM technology. It has been revealed from the roughness measurements of cube and cone samples, that roughness values are higher as compared to strip sample and in almost the same range in the build direction irrespective of the shape. The variation of surface roughness as a function of nozzle temperature has also shown that it is also dependent on the nozzle temperature while keeping other parameters constant. The experiments on the improvement in the surface quality of FDM parts was also performed using chemical and physical methods. Tetrahydrofuran, Dichloromethane and Acetone were found compatible with polycarbonate to improve surface without compromising the geometrical shape. Similarly Acrylonitrile Butadiene Styrene had excellent response to Acetone vapour smoothing both in terms of surface roughness and part symmetry. The surface roughness of PLA was also improved after treatment with Tetrahydrofuran. Co-Polyester, although had good surface after treatment with Tetrahydrofuran and Dichloromethane, but the part symmetry was disturbed.

1 December 2019 in Materials Research Express
Verified
Journal Article
Open access
MGMunazza Gul
Munazza Gul
MJMohsan Jelani
Mohsan Jelani
Najam Ul HassanNajam Ul Hassan
Najam Ul Hassan
MNM. Naeem
M. Naeem
SRSobia Allah Rakha
Sobia Allah Rakha
AMArshad Munir
Arshad Munir

10 May 2024 in Journal of Reinforced Plastics and Composites
Verified
Journal Article
Closed access
SHSyed Hameed Hussain
Syed Hameed Hussain
AKAqeel Ahsan Khurram
Aqeel Ahsan Khurram
AMAdnan Munir
Adnan Munir
MKMuhammad Salman Khan
Muhammad Salman Khan
AMAamir Mubashar
Aamir Mubashar
The effect of nano particle inclusion and the stacking sequence/metal volume fraction on the tensile strength and energy absorption properties of Fiber Metal Laminates (FML) is investigated. The FML structure is composed of lightweight thin sheets of aerospace grade aluminum alloy 7075 and unidirectional glass fiber composite sheets with Araldite LY5052 thermoset epoxy system as the matrix. The volume fraction of aluminum sheets in the FML structure was varied by increasing the number of aluminum sheets from 2 to maximum 4. In the second batch, the epoxy matrix is reinforced with of multi-walled carbon nano tubes and nano diamond particles together, each with 0.15 wt%. The purpose is to enhance the properties of the epoxy matrix to facilitate higher inter-laminate adhesion (FRP and aluminum). The results of the tensile testing show that with the increase of the metal volume fraction, the tensile strength as well energy absorbing capability (toughness) both are increased. The inclusion of the nano-reinforcements has increased the tensile strength and the toughness of the FML structure as compared to that of the FMLs without nano particles. The strength-to-weight ratio of FML structures is also increased after the inclusion of nano reinforced as desired for aerospace applications.