This paper presents an improved integrated on-board charger (IOBC) tailored for a 4-phase switched reluctance motor (SRM) drive. The proposed IOBC is non-isolated and utilizes the totem pole power factor correction (PFC) operation for reduced common-mode voltage. Furthermore, the proposed system accommodates bidirectional functions, ensuring versatility during charging mode. A non-isolated IOBC for SRM with reduced common-mode voltage and bidirectional capability has largely been ignored in the literature. The proposed system utilizes a modified Miller converter in the motoring mode and is easily reconfigured into a two-phase interleaved totem pole converter during charging modes without the need for any magnetic contactors. The proposed system features zero instantaneous torque (ZIT) at steady-state, ensuring minimal machine wear during charging modes. The proposed IOBC is controlled to ensure symmetric positive and negative grid currents for any given rotor position (during charging), thereby eliminating even harmonics and enhancing the power quality of grid current. The proposed system achieves charging power twice the motoring power with parallel-connected phase windings. Ansys electromagnetic transient simulation, MATLAB-based SRM drive simulations, experimental results, and comprehensive comparative analysis are presented to validate the various features and effectiveness of the proposed IOBC for SRM.
24 January 2014 in Journal of Vibration and Control
The operational efficiency and life of mechanical systems/structures depends to a large extent on their vibration control. Continuously occurring vibrations on the systems can cause fatigue and the effects of these vibrations are particularly severe if they occur at a frequency matching with that of the concerned system’s natural frequency – a stage called resonance. This paper focuses on achieving active vibration control of a smart cantilever beam at its first resonant frequency as it is at this stage that maximum damage to the system performance is expected. The smart system is modelled in the parametric domain using finite element modeling techniques and the obtained model is validated through experimental means. The active vibration control is achieved by employing two control algorithms namely – output feedback and error based control through general purpose operating system (LabVIEW on Windows 7) as well as in real time operating system (LabVIEW FPGA coupled with compact reconfigurable input output modules) and the performances are compared thereby justifying the importance of the deterministic and reliable real time control over the usual PC based control in experimental studies.
The growing demand for efficient and compact power conversion systems in electric vehicles (EVs), renewable energy systems, DC microgrids, and both portable and stationary medical equipment has intensified research into non-isolated high-gain bidirectional DC-DC converters. Existing solutions often employ transformer-based topologies or coupled inductors, which introduce increased cost, size, and control complexity. This paper presents a novel transformerless bidirectional high-gain DC-DC converter based on a modified Single-Ended Primary Inductor Converter (SEPIC) architecture. The proposed topology incorporates an Active Switched Inductor (ASL) at the input stage to achieve a wide voltage conversion ratio while ensuring reduced voltage stress on the maximum power switches. A key feature of the converter is its ability to provide bidirectional buck–boost operation in both power flow directions, while maintaining a reduced component count and improved efficiency through synchronous rectification. The converter’s performance is thoroughly analyzed under both continuous conduction mode (CCM) and discontinuous conduction mode (DCM). Furthermore, detailed small-signal modeling and closed-loop controller design are developed for both voltage-mode and current-mode control. A 200 W experimental prototype employing SiC MOSFETs is implemented to validate the theoretical analysis. Experimental results confirm the high efficiency, robust dynamic response, and practical feasibility of the proposed converter for next-generation power conversion applications.
All mechanical systems suffer from undesirable vibrations during their operations. These vibrations are unavoidable as they depend on various factors. However, for efficient operation of the system, they have to be controlled within the specified limits. Light weight, rapid and multi-mode control of the vibrating structure is possible by the use of piezoelectric sensors and actuators coupled with feedback algorithms. In this paper, direct output feedback based active vibration control has been implemented on a smart cantilever beam at its resonant frequency using PZT (Lead Zirconate Titanate) sensors and actuators. The work aims to showcase the performance abilities of the conventional PC based control and a dedicated REAL TIME CONTROL at resonance. The platform used is LABVIEW RT with FPGA hardware and the system performance is compared with the conventional time multiplexed Operating System (Windows 7) where LABVIEW is again used with the appropriate DAQ devices.