22 June 2021 in Lab on a Chip
In digital microfluidics, droplet generation is a fundamental operation for quantitative liquid manipulation. The generation of well-defined micro-droplets on a chip with restricted device geometries has become a real obstacle for digital microfluidics platforms to be used in parallel for in vitro diagnostic applications. Here, we propose a “one-to-three” droplet splitting technique that is able to generate sub-microlitre droplets beyond the “well-known” geometry limit in electrowetting-on-dielectric digital microfluidics. Accordingly, we realized an on-chip magnetic bead chemiluminescence immunoassay for parallel detection with the “one-to-three” technique. With the help of the generated micro droplets, we were able to retain the magnetic beads by a significantly reduced magnetic force. We have shown the detection of five B-type natriuretic peptide analyte samples on a single chip for around 10 minutes. The correlation coefficient of the calibration curve was 0.9942, and the detection limit was lower than 5 pg mL−1.
1 May 2023 in Applied Physics Letters
High-efficient droplet generation is crucial in microfluidics platforms in bio-applications. Among the microfluidic techniques, digital microfluidics, although with the capability of programmatically manipulating the droplets, is less effective in high-throughput droplets generation. In this Letter, a continuous “one-to-two” droplet generation strategy on digital microfluidics platform is achieved with an exponential generation efficiency, while overcoming the restriction on the droplet geometries (aspect ratio) in a wide range. An energy-based sub-droplet generation model is also proposed, as an expansion to the previous Laplace pressure-based geometrical model. The electrical parameters are taken into computing the sub-droplet generation on digital microfluidics from the aspect of energy. The proposed continuous “one-to-two” droplet generation strategy can generate sub-droplets with a minimized electrodes' number while with a higher energy input in each operation. The exponential efficiency will open the era for high-throughput droplets' application developments in digital microfluidics.
1 August 2019 in Analytica Chimica Acta
14 April 2020 in SAE International Journal of Advances and Current Practices in Mobility
Numerical simulation of in-cylinder processes can significantly reduce the development and refinement costs of engines. While it can be argued that higher fidelity models improve accuracy of prediction, it comes at the expense of high computational cost. In this respect, a 3D analysis of in-cylinder processes may not be feasible for evaluating large number of design and operating conditions. The situation can be more foreboding for transient simulations. In the current work a phenomenological combustion modeling approach is explored that can be implemented in a lower fidelity modeling framework and can approach the accuracy of higher dimensional models with significant reduction in computational cost. The proposed model uses transported probability density function (tPDF) method within a 0D framework to provide a computationally efficient solution while capturing the essential physics of in-cylinder combustion. Scalar mixing is accounted for by a modified Euclidean Minimum Spanning Tree (EMST) mixing model. A new model has been formulated to calculate the mixing timescale using the velocity-composition-frequency (VCF) tPDF method. Numerical comparisons have been performed for two engines: one with a 3D-CFD simulated diesel engine to compare the in-cylinder composition and thermal stratification, and one with a diesel engine where measured data is available over a range of operating conditions encompassing a range of speed, load, and exhaust-gas recirculation (EGR). A 42-species chemical mechanism including thermal NO is used to represent the gas-phase chemistry. The proposed 0D-VCF model predicted pressure, heat-release-rate, equivalence-ratio vs temperature distribution, and NOx are compared to the 3D-CFD data, as well as to the experimentally measured data. The proposed model was able to capture the 3D-CFD trend of equivalence-ratio vs temperature distribution at different crank-angle degrees quite accurately. The 0D-VCF model computed pressure and heat-release-rate along with the NOx showed reasonable agreement with the experiment. In summary, the proposed 0D numerical model has the potential to provide a computationally less expensive alternative to a 3D numerical simulation for estimating engine performance and engine-out emission quantities when transient or large number of operating points are to be simulated.