1 June 2020 in Applied Ocean Research
21 October 2018 in Biofouling
There are limited scientific data on contributors to the added drag of in-service ships, represented by modern-day coating roughness and biofouling, either separately or combined. This study aimed to gain an insight into roughness and hydrodynamic performance of typical coatings under in-service conditions of roughened ships’ hull surfaces. Comprehensive and systematic experimental data on the boundary layer and drag characteristics of antifouling coating systems with different finishes are presented. The coating types investigated were linear-polishing polymers, foul-release and controlled-depletion polymers. The data were collected through state-of-the-art equipment, including a 2-D laser Doppler velocimetry (LDV) system for hydrodynamic data in a large circulating water tunnel. Three coating systems were first applied on flat test panels with ‘normal’ finishes in the first test campaign to represent coating applications under idealised laboratory conditions. In order to address more realistic roughness conditions, as typically observed on ships’ hulls, ‘low’ and ‘high’ roughness densities were introduced into the same types of coating, in the second test campaign. The data collected from the first test campaign served as the baseline to demonstrate the effect on the surface roughness and hydrodynamic drag characteristics of these coating types as a result of ‘in-service’ or ‘severely flawed’ coating application scenarios. Data collected on coatings with a range of in-service surface conditions provided a basis to establish correlation between the surface roughness characteristics and hydrodynamic performance (roughness function). The findings of the study indicate that the estimations of drag penalties based on well-applied, relatively smooth coating conditions underestimate the importance of hull roughness, which although undesirable, is commonplace in the world’s commercial fleet.
1 October 2019 in Progress in Organic Coatings
7 February 2020 in Biofouling
This paper describes the design of an enhanced, plane channel, flowcell and its use for testing large-scale coated plates (0.6 m × 0.22 m) in fully developed flow, over a wide range of Reynolds numbers, with low uncertainty. Two identical, hydraulically smooth plates were experimentally tested. Uniform biofilms were grown on clean surfaces to test skin friction changes resulting from different biofilm thickness and densities. A velocity survey of the flowcell measurement section, using laser Doppler anemometry, showed a consistent velocity profile and low turbulence intensity in the central flow channel. The skin friction coefficient was experimentally determined using a pressure drop method. Results correlate closely to previously published regression data, particularly at higher speeds. Repeated measurements indicated very low uncertainty. This study demonstrates this flowcell’s applicability for representing consistent frictional drag of ship hull surfaces, enabling comparability of hydrodynamic drag caused by surface roughness to the reference surface measurements.
28 November 2018 in Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment
The prediction of hydrodynamic performance of hull coatings with different surface conditions is a challenging task. Moreover, with the emergence of new prototype coatings that are relatively smooth in terms of roughness characteristics, the accurate estimation of their drag is particularly important, as this will enable a good grading of drag reducing benefits of coatings. In the context of coating studies, the experimental methods are considered as the backbone and results obtained from experimental facilities with the required performance will enable accurate scaling of test results to full-scale ship results. Although numerical simulations like computational fluid dynamics have acquired the level of accuracy good enough to replace some of the systematic model testing used for ship design optimization, it is still not evident whether the simulations will be able to replicate the physical reality such as coating type, its roughness and biofilms accurate enough to enable predictions of the power requirements for ships. Therefore, this article gives insight into various coating hydrodynamic testing facilities and methods that are capable of measuring drag characteristics of coatings. The work highlights the details of each method and identifies the concepts and parameters needed to describe, implement and analyze hydrodynamic coating drag measurements. This article also summarizes the merits and demerits of each type of facility based on reports and studies reported in open literature. Finally, the authors propose a recommendation that can be incorporated into the design of the new hydrodynamic facility.
1 October 2024 in Biofouling
This research study delves into the hydrodynamic frictional characteristics of fouled panels coated with different types of coatings, investigating how fouling coverage and surface roughness influence drag. The investigation incorporates data on the overall percentage coverage of fouling, as well as roughness measurements obtained through a 3D profilometer. Drag data collected from a flowcell simulation of real-world flow conditions complements these measurements. Notably, the determination of the level of fouling leverages the capabilities of CIE L*a*b as an image analysis method, focusing on the overall coverage rather than individual fouling species. The objective is to illustrate how fouled panels perform under varying flow and coating conditions compared to their clean counterparts. Furthermore, the paper proposes a roughness scaling approach that considers both the percentage coverage and measured areal roughness for each coating type, encompassing both fouled and unfouled areas. This approach provides valuable insights into the combined effects of fouling and surface roughness on hydrodynamic performance, enhancing our understanding of the intricate interplay between these factors.